manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

Functional Description

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

17-5

17.2.1.1.1   Basic Direct Mode

In basic direct mode, the DMA controller does not read descriptors from memory, but instead 
uses the current parameters programmed in the DMA registers to start the DMA transfer. 
Software is responsible for initializing SARn, SATRn, DARn, DATRn, and BCRn registers. The 
DMA transfer is started when MRn[CS] is set. Software is expected to program all the 
appropriate registers before setting MRn[CS] to a 1. The transfer is finished after all the bytes 
specified in the byte count register have been transferred or if an error condition occurs. The 
sequence of events to start and complete a transfer in basic direct mode is as follows:

1.

Poll the channel state (see Table 17-2), to confirm that the specific DMA channel is 
idle.

2.

Initialize SARn, SATRn, DARn, DATRn and BCRn. 

3.

Set the mode register channel transfer mode bit, MRn[CTM], to indicate direct mode. 
Other control parameters may also be initialized in the mode register. 

4.

Clear then set the mode register channel start bit, MRn[CS], to start the DMA transfer.

5.

SRn[CB] is set by the DMA controller to indicate the DMA transfer is in progress.

6.

SRn[CB] is automatically cleared by the DMA controller after the transfer is finished, or 
if the transfer is aborted (MRn[CA] transitions from a 0 to 1), or if a transfer error 
occurs.

7.

End of segment interrupt is generated if MRn[EOSIE] is set.

17.2.1.1.2   Basic Direct Single-Write Start Mode

In basic direct single-write start mode, the DMA controller does not read descriptors from 
memory, but instead uses the current parameters programmed in the DMA registers to start the 
DMA transfer. Software is responsible for initializing the SATRn, DATRn, and BCRn registers. 
Setting MRn[SRW] configures the DMA controller to begin the DMA transfer either when SARn 
is written or when DARn is written, determined by the state of MRn[CDSM/SWSM]. Writing to 
SARn initiates the DMA transfer if MRn[CDSM/SWSM] is set. Writing to DARn initiates the 
DMA transfer if MRn[CDSM/SWSM] is cleared. The DMA controller automatically sets the 
channel start bit, MRn[CS]. Software is expected to program all the appropriate registers before 
writing the source or destination address registers. The transfer is finished after all the bytes 
specified in the byte count register have been transferred or if an error condition occurs. The 
sequence of events to start and complete a transfer in single-write start basic direct mode is as 
follows:

1.

Poll the channel state (see Table 17-2), to confirm that the specific DMA channel is 
idle.

2.

Initialize the source attributes (SATRn), DATRn, and BCRn registers. 

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
Farallon NetLINE USB User Manual preview
NetLINE USB
Brand: Farallon Pages: 26
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
Laird OL 4503 Specification And User Manual preview
OL 4503
Brand: Laird Pages: 36
Phytec L-843e.A1 Hardware Manual preview
L-843e.A1
Brand: Phytec Pages: 53
ZyXEL Communications EOC350 Series Quick Start Manual preview
EOC350 Series
Brand: ZyXEL Communications Pages: 2
Dahua NVS0X04DH Quick Start Manual preview
NVS0X04DH
Brand: Dahua Pages: 24
OpenVox B800P User Manual preview
B800P
Brand: OpenVox Pages: 13
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Brand: ICP DAS USA Pages: 8
ADS Technologies PTV-352-EFG Hardware Quickmanual preview
PTV-352-EFG
Brand: ADS Technologies Pages: 1
Arbor Technology Em104P-i2904 Quick Installation Manual preview
Em104P-i2904
Brand: Arbor Technology Pages: 8
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Brand: Riverbed Pages: 82
Compro Technology RS-2104 Quick Installation Manual preview
RS-2104
Brand: Compro Technology Pages: 2
Rainbow QPBB Instruction Manual preview
QPBB
Brand: Rainbow Pages: 2
Intercoax IXWB-450 Quick Start Manual preview
IXWB-450
Brand: Intercoax Pages: 2
sound4 STREAM X Maintenance And Operation Instruction Manual preview
STREAM X
Brand: sound4 Pages: 66
Echelon i.LON SmartServer Hardware Manual preview
i.LON SmartServer
Brand: Echelon Pages: 34

Brands by name

Popular brands

Load more brands