manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

17-2

 Freescale 

Semiconductor

RapidIO Interface Dedicated DMA Controller

17.1

Overview

The dedicated DMA controller has four high-speed DMA channels. Each one of the DSP cores 
can initiate DMA transfers. All channels are capable of complex data movement and advanced 
transaction chaining. Operations, such as descriptor fetches and block transfers, are initiated by 
each channel. A channel is selected by the arbitration logic and information is passed to the 
source and destination control blocks for processing. The source and destination blocks generate 
read and write requests to the address tenure engine, which manages the DMA master port 
address interface. After a transaction is accepted by the master port, control is transferred to the 
data tenure engine that manages the read and write data transfers. A channel remains active in the 
shared resources for the duration of the data transfer unless the allotted bandwidth per channel is 
reached.

17.1.1

Features

The dedicated DMA controller offers the following features:

„

Four high-speed/high-bandwidth channels accessible by local and remote masters

„

Basic DMA operation modes (direct, simple chaining)

„

Extended DMA operation modes (advanced chaining and stride capability)

„

Cascading descriptor chains

„

Misaligned transfers

„

Programmable bandwidth control between channels

„

Three priority levels supported for source and destination transactions 

„

Interrupt on error and completed segment, list, or link 

„

An Address Translation Management Unit (ATMU) with 10 local access address 
windows. The ATMU translates a request address into a logical device source/destination.

17.1.2

Modes of Operation

The MPC8144E dedicated DMA controller has two modes of operation: basic and extended. 
Basic mode is the DMA legacy mode. It does not support advanced features. Extended mode 
supports advanced features like striding and flexible descriptor structures.

These two basic modes allow users to initiate and end DMA transfers in various ways. Table 
17-1 summarizes the relationship between the modes and the following features:

„

Direct mode. No descriptors are involved. Software must initialize the required fields as 
described in Table 17-1 before starting a transfer.

„

Chaining mode. Software must initialize descriptors in memory and the required fields as 
described in Table 17-1 before starting a transfer.

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

TC Electronic M300 Service Manual preview
M300
Brand: TC Electronic Pages: 2
D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 4
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Brand: D-Link Pages: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Brand: D-Link Pages: 8
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Brand: D-Link Pages: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Brand: D-Link Pages: 88
Samsung SWC-E100 Quick Start Manual preview
SWC-E100
Brand: Samsung Pages: 2
Samsung iDCS 500 Manual preview
iDCS 500
Brand: Samsung Pages: 31
Samsung DDR3 Product Manual preview
DDR3
Brand: Samsung Pages: 15
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
Softing CAN-PRO1-PCIE Hardware User Manual preview
CAN-PRO1-PCIE
Brand: Softing Pages: 4
Moxa Technologies PT-7324 Series User Manual preview
PT-7324 Series
Brand: Moxa Technologies Pages: 36
ANEP P4GU VoLTE Technical Data Sheet preview
P4GU VoLTE
Brand: ANEP Pages: 48
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142

Brands by name

Popular brands

Load more brands