Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 443 / 1374

background image

Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

11-29

11.8.4 L2 ICache LRM State Register (L2IC_LRM)

This register holds the state of the Line Replacement Mechanism (LRM) of the cache, which is
PLRU in this implementation. The PLRUB[3–0] fields hold the PLRU state of the cache lines
pointed to by the debug counter. There are seven PLRU bits for each index in the cache to
determine the line to be replaced. The PLRU bits are updated when a new line is allocated or
replaced and when there is a line hit. A line is selected for replacement according to the PLRU bit
encoding shown in Table 11-10 (initial values of B[6–0] is all zeros). This register is read only,
accessible only in L2 ICache debug mode. Table 11-9 defines the L2IC_LRM bit fields.

CGL

1

0

Cache Global Lock
Indicates whether cache is in global lock mode or
not. Assertion of global lock mode is ignored during
a cache sweep operation.

0

Cache global lock mode not active.

1

Cache global lock mode active.

CE

0

0

Cache Memory Enabled
Indicates whether the two L2 cache memory
modules are enabled or disabled. At reset
deassertion, the two modules are disabled. Once
the cache memory is enabled. it may be disabled
only by reset. In disable mode the clock inside each
memory module is disabled and power is saved.
Note:

This is a sticky bit.

0

Cache memory disabled.

1

Cache memory enabled.

L2IC_LRM

L2 ICache LRM State Register

Offset 0x0C

Bit

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

—

PLRUB3

—

PLRUB2

Type

R

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

—

PLRUB1

—

PLRUB0

Type

R

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Table 11-9. L2IC_LRM Bit Descriptions

Name

Reset

Description

Settings

—

31

0

Reserved. Write to zero for future compatibility.

PLRUB3

30–24

0

PLRU Bits 3
Holds the state bits for indexes (4

×

i) + 3 (i is an

integer).

0

Cache line not valid.

1

Cache line valid.

—

23

0

Reserved. Write to zero for future compatibility.

PLRUB2

22–16

0

PLRU Bits 2
Holds the state] bits for indexes (4

×

i) + 2 (i is an

integer).

0

Cache line not valid.

1

Cache line valid.

Table 11-8. L2IC_CR2 Bit Descriptions (Continued)

Name

Reset

Description

Settings

«
...
441
442
443
444
445
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: ABB Pages: 66

Brand: Maco Pages: 38

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: vPipes Pages: 3

Brand: Zonet Pages: 2

Brand: LevelOne Pages: 31

IPS Pro-Module-24C-GE-BP-TM

Brand: Trend Micro Pages: 3

zoomno MSC-5578

Brand: BIIZZY Pages: 2

Brand: Compal Pages: 47

Brand: COUGAR Pages: 2

NC-MCO - TECHNICAL

Brand: Crest Audio Pages: 2

Brand: FOR-A Pages: 37

-K6-2/450 - MHz Processor

Brand: AMD Pages: 98

Brand: YASKAWA Pages: 87

Brand: SilverStone Pages: 12

Supereta Series DC/DC

Brand: TDK Pages: 2

Brand: Lenze Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands