manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

6-22

 Freescale 

Semiconductor

Boot Program

„

0x900D900D is written to 0xC007B00C in M2 indicating that the boot has finished 
executing. 

„

All cores jump to the address written in 0xC007B010. The value in this address should be 
written during the boot loading process.

6.7 System after Boot 

„

All MATTs in the MMUs are set to their reset value values (except M_xSDBx[PBS] 
which is set to 0x2). 

„

L1 I-Cache is enabled, but there are no cacheable windows.

„

All NMIs will be configured as NMIs in the EPIC.

„

VBA equals 0xFEF17000. Any interrupt other than 91 and 92 in the EPIC puts the core in 
debug.

„

EDC is enabled.

„

Core register values are not guaranteed and should be initialized before use.

6.8 Boot Errors

If the boot code fails, an indication as to the root cause is written to 0xC007B004. The possible 
reasons are listed in Table 6-3. 

Table 6-3.  Boot Error Codes

Error Code

Description

0x003FEFFF

Catastrophic Error. SmartDSP OS Function failed.

0x003FEFFD

Corrupted boot file. The possible causes are:
• Checksum wrong in TFTP file
• Checksum wrong in I

2

C file

• Unsupported S-Record type

0x003FEFFC

TFTP server time out

0x003FEFFB

Empty frame from TFTP server

0x003FEFFA

TFTP server sent ERROR code (05)

0x003FEFF9

Unsupported boot port

0x003FEFF8

Reset slave does not respond

0x003FEFF6

Using boot with RCWHR[STTM] equaling 1

0x003FEFF5

Boot port isn’t supported with current pin multiplexing.

0x003FEFF4

Too many I

2

C RCW slaves in address 0x11 of the EEPROM

0x003FEFF3

Error in protocol between I

2

C RCW master and slave 

0x003FEFF2

Boot port trying to write to area designated for boot (0xC007B014–0xC007FFFF)

0x0027EFFE

Lost arbitration on I

2

C bus.

0x0027EFFD

Time-out on I

2

C acknowledge (9th clock).

0x0027EFFC

Stuck SDA (I

2

C bus).

0x00000000

Unexpected debug condition in the SC3400 Core (unexpected interrupt, EE0 asserted 
and so on)

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Abus TVVR36500 User Manual preview
TVVR36500
Brand: Abus Pages: 60
Radwin Transportation FiberinMotion Deployment Manual preview
Transportation FiberinMotion
Brand: Radwin Pages: 122
Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
Parker ACR1200 Hardware Manual preview
ACR1200
Brand: Parker Pages: 50
janitza Procont LMC-008-IO User Manual And Technical Data preview
Procont LMC-008-IO
Brand: janitza Pages: 28
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
SeaLevel PC-ACB.MP User Manual preview
PC-ACB.MP
Brand: SeaLevel Pages: 21
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
Promise Technology Pegasus R4 Product Manual preview
Pegasus R4
Brand: Promise Technology Pages: 148
Williams Sound DW SY 1 User Manual preview
DW SY 1
Brand: Williams Sound Pages: 2
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
ZALMAN CNPS9900 Max User Manual preview
CNPS9900 Max
Brand: ZALMAN Pages: 9
Stepper Motor Canada DB25-1R5AM Manual preview
DB25-1R5AM
Brand: Stepper Motor Canada Pages: 7

Brands by name

Popular brands

Load more brands