Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 149 / 1374

background image

Serial Peripheral Interface (SPI) Signal Summary

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

3-41

3.9 Serial Peripheral Interface (SPI) Signal Summary

Table 3-11 summarizes the Serial Peripheral Interface (SPI) signal lines, which are available in all modes.

Table 3-11. SPI Signals

Signal Name

Type

Signal Description

GPIO24

IRQ6

SPISEL

Input/

Output

Input

Input

General-Purpose Input Output 24
One of 32 GPIOs. For details, see Chapter 25, GPIO. Valid in all modes.

Interrupt Request 6
One of sixteen external lines that can request a service routine via the internal interrupt
controller. For details, see Chapter 13, Interrupt Handling.

SPI Select
Enable input to the SPI slave in single master mode. In multi-master environment, SPISEL
detects an error when more one master is operating. Assertion of an SPISEL, while it is master,
causes an error.

GPIO23

IRQ5

SPIMISO

Input/

Output

Input

Input/

Output

General-Purpose Input Output 23
One of 32 GPIOs. For details, see Chapter 25, GPIO. Valid in all modes

Interrupt Request 5
One of sixteen external lines that can request a service routine via the internal interrupt
controller. For details, see Chapter 13, Interrupt Handling.

SPI Master Input Slave Output
When the SPI is a master, SPICLK is the clock input signal that shifts received data in from
SPIMOSI and transmitted data out through SPIMISO.

GPIO22

IRQ4

SPIMOSI

Input/

Output

Input

Input/

Output

General-Purpose Input Output 22
One of 32 GPIOs. For details, see Chapter 25, GPIO. Valid in all modes.

Interrupt Request 4
One of sixteen external lines that can request a service routine via the internal interrupt
controller. For details, see Chapter 13, Interrupt Handling.

SPI Master Output Slave Input
When the SPI is a master, SPICLK is the clock input signal that shifts received data in from
SPIMOSI and transmitted data out through SPIMISO.

GPIO21

IRQ1

SPICLK

Input/

Output

Input

Input/

Output

General-Purpose Input Output 21
One of 32 GPIOs. For details, see Chapter 25, GPIO. Valid in all modes.

Interrupt Request 1
One of sixteen external lines that can request a service routine via the internal interrupt
controller. see Chapter 13, Interrupt Handling.

SPI Clock
Gated clock, active only during data transfers. Four combinations of SPICLK phase and polarity
can be configured. When the SPI is a master, SPICLK is the clock output signal that shifts
received data in from SPIMOSI and transmitted data out through SPIMISO.

«
...
147
148
149
150
151
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

HiGain HLU-231 List 8F

Brand: ADC Pages: 7

Brand: vPipes Pages: 3

Brand: A4Tech Pages: 8

Brand: Moxa Technologies Pages: 36

Brand: Comelit Pages: 19

Brand: IBM Pages: 64

Brand: Icy Box Pages: 2

Open Standard Module RPX30 EVA-MI V1

Brand: iesy Pages: 9

Brand: Intel Pages: 578

Brand: Variscite Pages: 17

EK-Quantum Vector TUF RX 6800

Brand: ekwb Pages: 14

STM32MP157 Series

Brand: ST Pages: 47

Brand: El.Mo Pages: 16

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brand: Disc Makers Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands