Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 120 / 1374

background image

MSC8144E Reference Manual, Rev. 3

3-12

Freescale

Semiconductor

External Signals

3.5 Serial RapidIO Signals

Refer to Chapter 16, Serial RapidIO

Controller for configuration information.

ECC_MDM

Output

ECC Data Output Mask
Masks ECC data bytes transferred during a burst write. These signals are used to
support sub-burst-size transactions (such as single-byte writes) on SDRAM in which all
transactions occur in multi-byte bursts.

ECC_MDQS

Input/Output

ECC Data Strobe
Strobe for ECC data capture. The signal is driven as an input by the DDR SRAM with
read data and driven by the DDR controller as an output with write data. The strobes
may be single-ended or differential.

ECC_MDQS

Input/Output

ECC DQS Complement
Complement strobe for byte-lane data capture. The signal is driven as an input by the
DDR SRAM with read data and driven by the DDR controller as an output with write
data. The strobes may be single-ended or differential.

MDIC[0–1]

Input/Output

Driver Impedance Calibration
These lines are used for automatic calibration of the DDR I/O.

MODT[0–1]

Output

On-Die Termination
Memory controller outputs for the ODT to the SDRAM. Each signal represents the
corresponding chip select.

Table 3-7. Serial RapidIO Signals

Signal Name

Type

Description

SRIO_IMP_CAL_RX

Input

SRIO Receiver Impedance Control Signal
Receiver impedance calibration control signal.

SRIO_IMP_CAL_TX

Input

SRIO Transmitter Impedance Control Signal
Transmitter impedance calibration control signal.

SRIO_RXD0

Input

SRIO Receive Data 0
Serial data input for a 1x or 4x link. Each signal is part of a differential pair.

SRIO_RXD0

Input

SRIO Receive Data 0 Inverted
Inverted serial data input for a 1x or 4x link. Each signal is part of a differential
pair.

SRIO_RXD1

Input

SRIO Receive Data 1
Serial data input for a 4x link. Each signal is part of a differential pair.

SRIO_RXD1

Input

SRIO Receive Data 1 Inverted
Inverted serial data input for a 4x link. Each signal is part of a differential pair.

SRIO_RXD2

GE1_SGMII_RX

Input

Input

SRIO Receive Data 2
Serial data input for a 4x link. Each signal is part of a differential pair.

Ethernet 1 SGMII Receive Data
Part of the Ethernet signals. For details, see Chapter 20, Ethernet Controller.

SRIO_RXD3

GE2_SGMII_RX

Input

Input

SRIO Receive Data 3
Serial data input for a 4x link. Each signal is part of a differential pair.

Ethernet 2 SGMII Receive Data
Part of the Ethernet signals. For details, see Chapter 20, Ethernet Controller.

Table 3-6. Memory Controller Signals (Continued)

Signal Name

Type

Description

«
...
118
119
120
121
122
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: M-Audio Pages: 10

Brand: Commell Pages: 58

Brand: Profile Pages: 6

X-Pedition 2000

Brand: Enterasys Pages: 86

Brand: SriHome Pages: 12

Brand: Xantech Pages: 16

Brand: Zonet Pages: 1

Brand: LevelOne Pages: 4

EK-Quantum Vector TUF RX 6800

Brand: ekwb Pages: 14

STM32MP157 Series

Brand: ST Pages: 47

Brand: IBM Pages: 242

Brand: Cabletron Systems Pages: 56

EXTREME PROCESSOR UNIT

Brand: Jefftron Pages: 6

Brand: JETWAY Pages: 54

Brand: Data-Tronix Pages: 15

Brand: Acqiris Pages: 89

C32C824151 - UB E02 Print Server

Brand: Epson Pages: 84

Brand: Epson Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands