Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1103 / 1374

background image

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

25-1

Debugging, Profiling, and Performance
Monitoring

25

The MSC8144E device includes a number of mechanisms to evaluate and debug system
operation. These features include:

JTAG test access port (TAP) and boundary scan architecture

On-chip emulator (OCE) module in each core

Special debug and profiling elements in the device that permit:

— Event counting
— Entering debug mode after detection of a predefined state
— Special trace modes in the QUICC Engine module and DSP core subsystems
— Special debug errors
— Host reads and writes of all registers in debug mode

Performance monitoring of events occurring within internal modules including the L2
ICache, DMA controller, and RapidIO controller.

25.1

TAP, Boundary Scan, and OCE

The dedicated user-accessible test access port (TAP) is designed to be compatible with the IEEE
Std. 1149.1 test access port and boundary scan architecture. Problems associated with testing
high-density circuit boards led to development of this standard under the sponsorship of the test
technology committee of IEEE and the joint test action group (JTAG). The MSC8144E supports
circuit-board test strategies based on this standard. This section covers aspects of JTAG that are
specific to the MSC8144E. It includes the items that the standard requires to be defined, with
additional information specific to the MSC8144E device. For details on the standard, refer to the
IEEE Std. 1149.1 documentation.

The JTAG port also provides access to the on-chip emulator (OCE) module, a dedicated block for
debugging applications. Therefore, this section includes information on registers and
functionality of the OCE module that are specific to the MSC8144E. For details on the OCE
module functionality, see the OCE Architecture Manual.

The SC3400 core OCE module interfaces with the SC3400 core and its peripherals
non-intrusively so that you can examine registers, memory, or on-device peripherals, thus
facilitating hardware and software development on the SC3400 core-based devices. Special

«
...
1101
1102
1103
1104
1105
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Patton electronics Pages: 8

Brand: PaloAlto Networks Pages: 3

Brand: Patton electronics Pages: 16

OfficeConnect WX2200

Brand: 3Com Pages: 204

Brand: Idis Pages: 86

Brand: Paradyne Pages: 2

Brand: Stanwax Laser Pages: 9

Brand: Alesis Pages: 46

Urban Wireless CC-VT240W

Brand: Cateye Pages: 15

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

HHM Series HHM2245SA1

Brand: TDK Pages: 2

Brand: Giacomini Pages: 2

Brand: Caen Pages: 14

Brand: Technics Pages: 20

Brand: Dataprobe Pages: 16

Brand: swiftech Pages: 2

CORE 2 DUO E4000 - 3-2008

Brand: Intel Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands