Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1007 / 1374

background image

TDM Programming Model

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

19-71

19.7.3.8 TDMx Adaptation Status Register (TDMxASR)

Table 19-42. TDMxTER Bit Descriptions

Name

Reset

Description

Settings

—

31–5

0

Reserved. Write to zero for future compatibility.

TFSTI

4

0

Transmit First or Second Threshold Interrupt
Indication
Indicates whether the last receive threshold interrupt is the
first or second threshold.

0

Second threshold interrupt.

1

First threshold interrupt.

TSE

3

0

Transmit Sync Error
Indicates whether a sync error has occurred. TSE is set
when the transmit frame synchronization is lost (the
synchronization state change from SYNC to HUNT state)
because that a transmit frame sync arrive early or it not
recognized at the expected position. During operation, this
bit indicates errors on the transmit signals of the TDM
module. For details, see Section 19.2.4.3

0

Normal operation. No transmit
sync error has occurred.

1

A transmit sync error has
occurred.

ULBE

2

0

Underrun Local Buffer Event
Indicates whether an underrun event has occurred in the
TDM local buffer. This error should not occur during normal
operation. It indicates that the TDM has not received
enough bandwidth on the internal MBus and therefore
cannot read the data from the data buffers to the TDM local
memory. For details, see Section 19.2.6.

0

No underrun event has occurred
in the TDM local memory.

1

An underrun event has occurred
in the TDM local memory.

TFTE

1

0

Transmit First Threshold Event
Indicates whether a first threshold event has occurred.
TFTE is set when the first threshold of all the transmit data
buffers is empty. The first threshold pointer is determined
by the Transmit First Threshold Register (TDMxTFTR). For
details, see Section 19.2.6.3.

0

No transmit first threshold event
has occurred.

1

A transmit first threshold event
has occurred.

TSTE

0

0

Transmit Second Threshold Event
Indicates whether a transmit second threshold event has
occurred. TSTE is set when the second threshold of all the
transmit data buffers is empty. The second threshold
pointer is determined by the transmit Second Threshold
Register (TDMxTSTR). For details, see Section 19.2.6.3.

0

No transmit second threshold
event has occurred.

1

A transmit second threshold
event has occurred.

TDMxASR

TDMx Adaptation Status Register

Offset 0x3F30

Bit

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

—

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

—

AMS

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

«
...
1005
1006
1007
1008
1009
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: ICP DAS USA Pages: 8

Brand: F5 Pages: 72

Brand: AMD Pages: 20

Brand: Oracle Pages: 24

Brand: Genie Pages: 15

Brand: LogLogic Pages: 30

Brand: N.A.T. Pages: 32

Brand: Infoblox Pages: 13

Brand: Atmel Pages: 2

Brand: ZALMAN Pages: 16

Brand: Advantech Pages: 66

Brand: UNICORECOMM Pages: 19

Brand: Xtreme Pages: 83

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Brand: IFM Pages: 12

Brand: Zonet Pages: 1

Cyclades CS4008

Brand: Avocent Pages: 2

Brand: Agilent Technologies Pages: 458

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands