Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 1000 / 1374

background image

MSC8144E Reference Manual, Rev. 3

19-64

Freescale

Semiconductor

TDM Interface

The TDMxTCPRn registers are implemented using a compiled memory, and include support of a
parity mechanism that allows detection and correction of one soft error using an interrupt (see
TDMxPCR on page 19-57).

19.7.2.10 TDMx Receive Interrupt Enable Register (TDMXRIER)

TDMxRIER has the same bit format as the TDMxRER registers. If an RIER bit is clear, the
corresponding event in the TDMxRER registers is masked (see page 19-69).

Table 19-33. TDMxTCPRn Bit Descriptions

Name

Reset

Description

Settings

TACT

31

—

Transmit Channel Active
Set when the transmit channel n is active.

0

The channel is non-active.

1

The channel is active.

TCONV

30–29

—

Transmit Channel Convert
Determines the type of the transmit channel n:
Transparent, A-law, or

μ

-Law.

00 Transmit channel n is a transparent

channel.

01 Transmit channel n is a

μ

-Law channel.

10 Transmit channel n is an A-Law

channel.

11 Reserved.

—

28

—

Reserved. Write to zero for future compatibility.

—

27–24

—

These bits are used for parity protection.

TCDBA

23–0

—

Transmit Channel Data Buffer Base Address
Determines the offset of the transmit data buffer n base
address from the Transmit Global Base Address
(TGBA). The TCDBA value should be 16 byte aligned;
that is, the four LSB should be clear. For details, see
Section 19.2.6.2.

0x000000–0xFFFFF0.

TDMxRIER

TDMx Receive Interrupt Enable Register

Offset 0x3F78

Bit

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

—

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

—

RSEEE OLBEE RFTEE RSTEE

Type

R/W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Table 19-34. TDMxRIER Bit Descriptions

Name

Reset

Description

Settings

—

31–4

0

Reserved. Write to zero for future compatibility.

RSEEE

3

0

Receive Sync Error Event Enable
Enable assertion of the receive error interrupt when the
Receive Sync Error (RSE) bit is set (see page 19-69).

0

Receive sync error is masked.

1

Receive sync error is enabled.

«
...
998
999
1000
1001
1002
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: Patton electronics Pages: 16

Brand: Ublox Pages: 17

Brand: XESS Pages: 23

Brand: protech Pages: 95

Kontron SMARC-sXEL

Brand: S&T Pages: 108

EK-FC750 GTX Series

Brand: ekwb Pages: 2

See3CAM 30 Z10X

Brand: e-con Systems Pages: 14

Brand: Cypress Semiconductor Pages: 26

Brand: Wavtech Pages: 8

NetStructure ZT 5085

Brand: Intel Pages: 106

Brand: IBM Pages: 8

Brand: XMOS Pages: 8

Brand: Rosewill Pages: 5

Brand: IBM Pages: 78

EK-FC670 GTX Series

Brand: ekwb Pages: 2

Brand: NovaStar Pages: 16

Brand: ekwb Pages: 36

MAG CORELIQUID C240

Brand: MSI Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands