manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

781

 

Preliminary—Subject to Change Without Notice

23.4.2

Host Interface

23.4.2.1

System Configuration

System Configuration Registers are described in 

Section 23.3.2, “System Configuration Registers

”. 

Detailed explanation on the configured functionalities is found throughout 

Section 23.4, “Functional 

Description

, and a specification for the initial configuration sequence is found on 

Section 23.5.1, 

“Configuration Sequence

”.

23.4.2.2

Interrupts and Data Transfer Requests

23.4.2.2.1

Interrupt Types and Sources

Each one of the eTPU channels can be a source of two requests: 

Channel Interrupt

 request and 

Data 

Transfer Request

. Channel Interrupts are targeted to a Host CPU. Data Transfer Requests may be targeted 

to a data transfer module (e.g., a DMA controller). Interrupt and Data Transfer registers are used by the 
Host to enable interrupts and data transfer requests, indicate their status and service them. Interrupt and 
Data Transfer requests have the same sets of registers and external signals, and are handled in the same 
way. They differ only by the fact that Data Transfer Requests are also cleared by the assertion of respective 
DMA completion acknowledge line. Data Transfer Requests can be used as another source for Host 
interrupts at MCU integration if not used with a DMA.

NOTE

Interrupt and Data Transfer requests can be cleared even when Engines are 
in Module Disable Mode, through the Global Channel Registers, and also 
DMA completion for Data Transfer requests.

Channel Interrupts and Data Transfer Requests can only be issued by eTPU microcode, through one of the 
Channel Control instruction fields (see 

Section 23.4.9.3.10, “Channel Interrupt and Data Transfer 

Requests

”).

Both Channel Interrupt and Data Transfer requests can be individually enabled for each channel.

eTPU Interrupt and Data Transfer Registers are mirrored in two organizations: grouped by Channel and 
grouped by type (interrupt status, interrupt enable, data transfer status, data transfer enable). This allows 
either “channel-oriented” or “bundled channel” Host interrupt service schemes, or a combination of them. 
For a detailed description, refer to 

Section 23.3.5, “Channel Registers Layout

” and 

Section 23.3.6, “Global 

Channel Registers

.”

eTPU can also assert a 

Global Exception

 interrupt indicating a global illegal state. There are three possible 

sources for a Global Exception:

•

Execution of an illegal instruction by the microengine (see 

Section 23.4.9.5, “Illegal Instructions

). 

This Global Exception source is flagged by the bits ILF1 and ILF2 in register ETPUMCR.

•

An SCM signature mismatch detected by the Multiple Input Signature Calculator - MISC. See 

Section 23.4.10.3.1, “SCM Test - Multiple Input Signature Calculator

. This source is flagged by 

the bit SCMMISF in register ETPUMCR.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

iCeeO2 C30 Instruction Manual preview
C30
Brand: iCeeO2 Pages: 7
Oceanic DX1 Product Service Manual preview
DX1
Brand: Oceanic Pages: 11
Goodson GEO-SC Instructions preview
GEO-SC
Brand: Goodson Pages: 4
Moeller TC-RMQ Installation Instructions preview
TC-RMQ
Brand: Moeller Pages: 2
IDTECK Star FINGER006 User Manual preview
Star FINGER006
Brand: IDTECK Pages: 51
Partlow MIC 1161 Operator'S Manual preview
MIC 1161
Brand: Partlow Pages: 49
Ascon tecnologic TLB 55 Operating Instruction preview
TLB 55
Brand: Ascon tecnologic Pages: 11
ROBOT3T THC3T-02 Operation Manual preview
THC3T-02
Brand: ROBOT3T Pages: 21
StudioComm Dante 792 User Manual preview
Dante 792
Brand: StudioComm Pages: 61
Unimig UNI-FLAME REG Operation Manual preview
UNI-FLAME REG
Brand: Unimig Pages: 4
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Brand: OCL Pages: 2
Danfoss PVE Series Installation Manual preview
PVE Series
Brand: Danfoss Pages: 6
VECTOR CONTROLS TCX2 Product Data Sheet preview
TCX2
Brand: VECTOR CONTROLS Pages: 10
ADLINK Technology cPCI-7252 User Manual preview
cPCI-7252
Brand: ADLINK Technology Pages: 54
Aqua Lung Legend LX Second Stage Technical Maintenance Manual preview
Legend LX Second Stage
Brand: Aqua Lung Pages: 18
Hanna Instruments HI 9912 Instruction Manual preview
HI 9912
Brand: Hanna Instruments Pages: 28
Bard CompleteStat CS9B-THOA Quick Start Manual preview
CompleteStat CS9B-THOA
Brand: Bard Pages: 10
Mono DELTA DEPOSITOR Operation Manual preview
DELTA DEPOSITOR
Brand: Mono Pages: 60

Brands by name

Popular brands

Load more brands