Freescale Semiconductor MPC5632M Manual Download Page 714

Page: 714 / 1384

MPC563XM Reference Manual, Rev. 1

714

Freescale Semiconductor

Preliminary—Subject to Change Without Notice

Figure 22-84. Time base generation with external clock and clear on match start

Figure 22-85. Time base generation with internal clock and clear on match start

Figure 22-86. Time base generation with clear on match end

system clock

input event

internal counter

match value = 3

see note 1

Note 1: When a match occurs, the first system clock cycle is used to clear the

internal counter, and at the next edge of prescaler clock enable

the counter will start counting.

FLAG set event

FLAG clear

FLAG pin/register

system clock

prescaler clock enable

internal counter

match value = 3

PRESCALED CLOCK RATIO = 3

see note 1

Note 1: When a match occurs, the first clock cycle is used to clear the

internal counter, and only after a second edge of pre scaled clock

the counter will start counting.

FLAG set event

FLAG clear

FLAG pin/register

system clock

input event/prescaler clock enable

internal counter

match value = 3

PRESCALED CLOCK RATIO = 3

see note 1

Note 1: The match occurs only when the input event/prescaler clock enable is active.

Then, the internal counter is immediately cleared.

FLAG set event

FLAG clear

FLAG pin/register

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MPC5632M

Reviews:

Brands by name

Popular brands

Freescale Semiconductor MPC5632M, Manual

Search results

Summary of Contents for MPC5632M

Reviews:

Brands by name

Popular brands