manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

1046

Freescale Semiconductor

 

Preliminary—Subject to Change Without Notice

Figure 24-64. ETRIG Event Propagation Example

24.6.4.6

CFIFO Scan Trigger Modes

The EQADC supports two different scan modes, single-scan and continuous-scan. Refer to 

Table 24-26

 

for a summary of these two scan modes. When a CFIFO is triggered, the EQADC scan mode determines 
whether the EQADC will stop command transfers from a CFIFO, and wait for software intervention to 
rearm the CFIFO to detect new trigger events, upon detection of an asserted EOQ bit in the last transfer. 
Refer to 

Section 24.6.2.3, “Message Format in EQADC

 for details about command formats. 

CFIFOs can be configured in single-scan or continuous-scan mode. When a CFIFO is configured in 
single-scan mode, the EQADC scans the CQueue one time. The EQADC stops future command transfers 
from the triggered CFIFO after detecting the EOQ bit set in the last transfer. After a EOQ bit is detected, 
software involvement is required to rearm the CFIFO so that it can detect new trigger events.

When a CFIFO is configured for continuous-scan mode, no software involvement is necessary to rearm 
the CFIFO to detect new trigger events after an asserted EOQ is detected. In continuous-scan mode the 
whole CQueue is scanned multiple times.

The EQADC also supports different triggering mechanisms for each scan mode. The EQADC will not 
transfer commands from a CFIFO until the CFIFO is triggered. The combination of scan modes and 
triggering mechanisms allows the support of different requirements for scanning input channels. The scan 
mode and trigger mechanism are configured by programming the MODEx field in 

Section 24.5.2.7, 

“EQADC CFIFO Control Registers (EQADC_CFCR)

.

Enabled CFIFOs can be triggered by software or external trigger events. The elapsed time from detecting 
a trigger to transferring a command is a function of clock frequency, trigger synchronization, trigger 
filtering or not, programmable trigger events, command transfer, CFIFO prioritization, CBuffer 
availability, etc. Fast and predictable transfers can be achieved by ensuring that the CFIFO is not 
underflowing and that the target CBuffer is not full when the CFIFO is triggered.

System Clock

External Trigger Signal

Filtered External

CFIFO Status

Trigger Signal

 Signal State at Input Pin

MODEx

IDLE

WAITING FOR TRIGGER

TRIGGERED

DISABLED

CONTINUOUS SCAN HIGH LEVEL GATED EXTERNAL TRIGGER

Trigger Detection Delay

Trigger Synchronization and Filtering Delay (Obs. 1)

Obs.

- 1: This delay is about 2 clocks when the filter bypass control is asserted.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

tbs electronics Omnicharge Solar OCS 100-20 Installation Manual preview
Omnicharge Solar OCS 100-20
Brand: tbs electronics Pages: 64
POLA HP49 Handbook preview
HP49
Brand: POLA Pages: 2
OPW PetroVend PV200 Options Installation preview
PetroVend PV200
Brand: OPW Pages: 2
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Brand: Swagelok Pages: 20
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Brand: Wavelength Electronics Pages: 17
Variotech ENA3 Manual preview
ENA3
Brand: Variotech Pages: 24
ICP DAS USA ISaGRAF WinCE ViewPAC User Manual preview
ISaGRAF WinCE ViewPAC
Brand: ICP DAS USA Pages: 192
Intiel Dynamic Boiler Controller User Manual preview
Dynamic Boiler Controller
Brand: Intiel Pages: 25
National Instruments sbRIO-9698 User Manual preview
sbRIO-9698
Brand: National Instruments Pages: 12
Lennox HYDROCONTROL Installation, Operating And Maintenance Manual preview
HYDROCONTROL
Brand: Lennox Pages: 34
Rohde ST 630 Operation Manual preview
ST 630
Brand: Rohde Pages: 344
TAC Vista TAC Xenta OP Manual preview
TAC Xenta OP
Brand: TAC Vista Pages: 2
Ellard V3D Maxi Product Instructions preview
V3D Maxi
Brand: Ellard Pages: 21
mikroElektronika mikromedia for ARM User Manual preview
mikromedia for ARM
Brand: mikroElektronika Pages: 35
SUPMEA SUP-DC2000 User Manual preview
SUP-DC2000
Brand: SUPMEA Pages: 40
Citadele Digipass 320 Operation Instructions Manual preview
Digipass 320
Brand: Citadele Pages: 6
Grifco C10A Installation And User Manual preview
C10A
Brand: Grifco Pages: 20
Magpowr DIGITRAC 2 Instruction Manual preview
DIGITRAC 2
Brand: Magpowr Pages: 22

Brands by name

Popular brands

Load more brands