Freescale Semiconductor MK22FN256VDC12 Reference Manual Download Page 172 | Manualshive

Page: 172 / 1313

background image

6.2.4 Reset Pin

For all reset sources except a VLLS Wakeup that does not occur via the RESET pin, the
RESET pin is driven low by the MCU for at least 128 bus clock cycles and until flash
initialization has completed.

After flash initialization has completed, the RESET pin is released, and the internal Chip
Reset negates after the RESET pin is pulled high. Keeping the RESET pin asserted
externally delays the negation of the internal Chip Reset.

6.2.5 Debug resets

The following sections detail the debug resets available on the device.

6.2.5.1 JTAG reset

The JTAG module generate a system reset when certain IR codes are selected. This
functional reset is asserted when EzPort, EXTEST, HIGHZ and CLAMP instructions are
active. The reset source from the JTAG module is released when any other IR code is
selected. A JTAG reset causes the RCM's SRS1[JTAG] bit to set.

6.2.5.2 nTRST reset

The nTRST pin causes a reset of the JTAG logic when asserted. Asserting the nTRST pin
allows the debugger to gain control of the TAP controller state machine (after exiting
LLS or VLLSx) without resetting the state of the debug modules.

The nTRST pin does not cause a system reset.

6.2.5.3 Resetting the Debug subsystem

Use the CDBGRSTREQ bit within the SWJ-DP CTRL/STAT register to reset the debug
modules. However, as explained below, using the CDBGRSTREQ bit does not reset all
debug-related registers.

CDBGRSTREQ resets the debug-related registers within the following modules:

• SWJ-DP
• AHB-AP

Reset

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

172

Freescale Semiconductor, Inc.

«
...
170
171
172
173
174
...
»

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

Brand: Maestra Pages: 22

Brand: Nabco Pages: 35

Brand: Elby Designs Pages: 4

Brand: Hiwin Pages: 99

EZ-ZONE PM L AAAAB Series

Brand: Watlow Pages: 30

Brand: Z-Wave Pages: 27

Brand: Espressif Systems Pages: 11

Brand: L&L KILNS Pages: 12

Brand: NXP Semiconductors Pages: 362

lyriQ AU7394 Series

Brand: On-Q Pages: 8

Brand: VAL Pages: 10

Brand: Zonet Pages: 2

Brand: Texas Instruments Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands