manualshive.com logo in svg

Freescale Semiconductor MK22FN256VDC12, Reference Manual

The Freescale Semiconductor MK22FN256VDC12 is a high-performance microcontroller ideal for various applications. You can easily access the Reference Manual and user manuals for free download from manualshive.com. Get detailed information on features, specifications, and programming instructions to maximize the potential of this versatile semiconductor product.

Share
Download
background image

SPIx_MCR field descriptions (continued)

Field

Description

0

Continuous SCK disabled.

1

Continuous SCK enabled.

29–28

DCONF

SPI Configuration.

Selects among the different configurations of the module.

00

SPI

01

Reserved

10

Reserved

11

Reserved

27

FRZ

Freeze

Enables transfers to be stopped on the next frame boundary when the device enters Debug mode.

0

Do not halt serial transfers in Debug mode.

1

Halt serial transfers in Debug mode.

26

MTFE

Modified Timing Format Enable

Enables a modified transfer format to be used.

0

Modified SPI transfer format disabled.

1

Modified SPI transfer format enabled.

25

PCSSE

Peripheral Chip Select Strobe Enable

Enables the PCS5/ PCSS to operate as a PCS Strobe output signal.

0

PCS5/ PCSS is used as the Peripheral Chip Select[5] signal.

1

PCS5/ PCSS is used as an active-low PCS Strobe signal.

24

ROOE

Receive FIFO Overflow Overwrite Enable

In the RX FIFO overflow condition, configures the module to ignore the incoming serial data or overwrite
existing data. If the RX FIFO is full and new data is received, the data from the transfer, generating the
overflow, is ignored or shifted into the shift register.

0

Incoming data is ignored.

1

Incoming data is shifted into the shift register.

23–22

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

21–16

PCSIS

Peripheral Chip Select x Inactive State

Determines the inactive state of PCSx.

0

The inactive state of PCSx is low.

1

The inactive state of PCSx is high.

15

DOZE

Doze Enable

Provides support for an externally controlled Doze mode power-saving mechanism.

0

Doze mode has no effect on the module.

1

Doze mode disables the module.

Table continues on the next page...

Chapter 44 Serial Peripheral Interface (SPI)

K22F Sub-Family Reference Manual , Rev. 3, 7/2014

Freescale Semiconductor, Inc.

1051

Summary of Contents for MK22FN256VDC12


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MK22FN256VDC12

Tapeswitch C6 Technical Manual preview
C6
Brand: Tapeswitch Pages: 13
Samsung SSA-P400 User Manual preview
SSA-P400
Brand: Samsung Pages: 27
Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
Warren Controls E024 Installation, Operation And Maintenance Instructions preview
E024
Brand: Warren Controls Pages: 28
EAS Electric ECRP86EKD Operating Manual preview
ECRP86EKD
Brand: EAS Electric Pages: 89
Hach SC4200c User Manual preview
SC4200c
Brand: Hach Pages: 36
Idex Pulsafeeder MPC Vector Installation, Operation & Maintenance Manual preview
Pulsafeeder MPC Vector
Brand: Idex Pages: 114
Linear Technology LTC3703 Manual preview
LTC3703
Brand: Linear Technology Pages: 32
LAMBERTI ELEKTRONIK Latherm HZR Comfort Operating Manual preview
Latherm HZR Comfort
Brand: LAMBERTI ELEKTRONIK Pages: 16
3M Touch Screen Controller SX112 Reference Manual preview
Touch Screen Controller SX112
Brand: 3M Pages: 33
V2 WES-ADI Instruction Manual preview
WES-ADI
Brand: V2 Pages: 60
ENGGA EVC800i Installation & Adjustment Manual preview
EVC800i
Brand: ENGGA Pages: 8
Powrmatic Eurotrol 2 Installation & User'S Instructions preview
Eurotrol 2
Brand: Powrmatic Pages: 10
Aube Technologies TH146-N-U Installation Manual preview
TH146-N-U
Brand: Aube Technologies Pages: 12
ELREHA TKC 19130 Technical Manual preview
TKC 19130
Brand: ELREHA Pages: 18
SOMFY animeo IB+ 4 Installation Manual preview
animeo IB+ 4
Brand: SOMFY Pages: 20
Vello Extenda LW-100 Quick Start Manual preview
Extenda LW-100
Brand: Vello Pages: 8
Sices DST4601/PX User Manual preview
DST4601/PX
Brand: Sices Pages: 19

Brands by name

Popular brands

Load more brands