manualshive.com logo in svg

Freescale Semiconductor MCF54455, Reference Manual

Share
Download
Freescale Semiconductor MCF54455 Reference Manual Download Page 769

DMA Serial Peripheral Interface (DSPI)

31-16

Freescale Semiconductor

31.3.5

DSPI DMA/Interrupt Request Select and Enable Register 
(DSPI_RSER)

The DSPI_RSER serves two purposes. It enables flag bits in the DSPI_SR to generate DMA requests or 
interrupt requests. The DSPI_RSER also selects the type of request to be generated. See the individual bit 
descriptions for information on the types of requests the bits support. Do not write to the DSPI_RSER 
while the DSPI is running.

15–12

TXCTR

TX FIFO counter. Indicates the number of valid entries in the TX FIFO. The TXCTR is incremented every time the 
DSPI _PUSHR is written. The TXCTR is decremented every time an SPI command is executed and the SPI data is 
transferred to the shift register.

11–8

TXNXTPTR

Transmit next pointer. Indicates which TX FIFO entry is transmitted during the next transfer. The TXNXTPTR field is 
updated every time SPI data is transferred from the TX FIFO to the shift register. See 

Section 31.4.2.4, “TX FIFO 

Buffering Mechanism,”

 for more details.

7–4

RXCTR

RX FIFO counter. Indicates the number of entries in the RX FIFO. The RXCTR is decremented every time the 
DSPI_POPR is read. The RXCTR is incremented after the last incoming databit is sampled, but before the t

ASC

 delay 

starts. Refer to 

Section 31.4.4.1, “Classic SPI Transfer Format (CPHA = 0)

” for details.

3–0

POPNXTPTR

Pop next pointer. Contains a pointer to the RX FIFO entry that is returned when the DSPI_POPR is read. The 
POPNXTPTR is updated when the DSPI_POPR is read. See 

Section 31.4.2.5, “RX FIFO Buffering Mechanism

” for 

more details.

Address

:

0xFC05_C030 (DSPI_RSER)

Access: User Read/Write

31

30

29

28

27

26

25

24

23

22

21

20

19

18

17

16

R TCF

_RE

0

0

EOQF

_RE

TFUF

_RE

0

TFFF

_RE

TFFF

_DIRS

0

0

0

0

RFOF

_RE

0

RFDF

_RE

RFDF

_DIRS

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 31-6.  DSPI DMA/Interrupt Request Select and Enable Register (DSPI_RSER)

Table 31-7. DSPI_RSER Field Descriptions

Field

Description

31

TCF_RE

Transmission complete request enable. Enables DSPI_SR[TCF] flag to generate an interrupt request.
0 TCF interrupt requests are disabled
1 TCF interrupt requests are enabled

30–29

Reserved, must be cleared.

Table 31-6. DSPI_SR Field Descriptions (continued)

Field

Description

Summary of Contents for MCF54455


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands