manualshive.com logo in svg

Freescale Semiconductor MCF5329, Reference Manual, Page: 584 / 924

Share
Download
Freescale Semiconductor MCF5329 Reference Manual Download Page 584

FlexCAN

23-20

Freescale Semiconductor

23.3.10 Functional Overview

The FlexCAN module is flexible in that each one of its 16 message buffers (MBs) can be assigned as a 
transmit buffer or a receive buffer. Each MB, which is up to 8 bytes long, is also assigned an interrupt flag 
bit that indicates successful completion of transmission or reception. 

An arbitration algorithm decides the prioritization of MBs to be transmitted based on the message ID or 
the MB ordering. A matching algorithm makes it possible to store received frames only into MBs that have 
the same ID programmed on its ID field. A masking scheme makes it possible to match the ID programmed 
on the MB with a range of IDs on received CAN frames. Data coherency mechanisms are implemented to 
guarantee data integrity during MB manipulation by the CPU.

Before proceeding with the functional description, an important concept must be explained. A message 
buffer is said to be active at a given time if it can participate in the matching and arbitration algorithms that 
are happening at that time. An Rx MB with a 0000 code is inactive (refer to 

Table 23-12

). Similarly, a Tx 

MB with a 1000 code is inactive (refer to 

Table 23-13

). An MB not programmed with 0000 or 1000 is 

temporarily deactivated (does not participate in the current arbitration/matching run) when the CPU writes 
to the C/S field of that MB.

23.3.11 Transmit Process

The CPU prepares or changes an MB for transmission by writing the following:

1. Control/status word to hold Tx MB inactive (CODE = 1000)

2. ID word

3. Data bytes

4. Control/status word (active CODE, LENGTH)

0

1010

1010

Transmit a data frame when a remote request frame with the 
same ID is received. This message buffer participates 
simultaneously in the matching and arbitration processes. The 
matching process compares the ID of the incoming remote 
request frame with the ID of the MB. If a match occurs, this 
message buffer is allowed to participate in the current arbitration 
process and the CODE field is automatically updated to 1110 to 
allow the MB to participate in future arbitration runs. When the 
frame is eventually transmitted successfully, the code 
automatically returns to 1010 to restart the process again.

0

1110

1010

This is an intermediate code automatically written to the 
message buffer as a result of match to a remote request frame. 
The data frame is transmitted unconditionally once, and then 
the code automatically returns to 1010. The CPU can also write 
this code with the same effect.

Table 23-13. Message Buffer Code for Tx Buffers (continued)

MBn[RTR]

Initial Tx 

Code

Code After 

Successful 

Transmission

Description

MCF5329 Reference Manual, Rev 3

Summary of Contents for MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments