manualshive.com logo in svg

Freescale Semiconductor MC9S12ZVM series, Reference Manual

Share
Download
Freescale Semiconductor MC9S12ZVM series Reference Manual Download Page 96

Chapter 2 Port Integration Module (S12ZVMPIMV1)

MC9S12ZVM Family Reference Manual  Rev. 1.3

96

Freescale Semiconductor

Table 2-3. Preferred Interface Configurations

NOTE

For standalone usage of SCI0 on external pins set
[S0L0RR2:S0L0RR0]=0b110 and disable the LINPHY0 (LPCR[LPE]=0).
This releases PS0 and PS1 to other associated functions and maintains
TXD0 and RXD0 signals on PT1 and PT0, respectively, if no other function
with higher priority takes precedence.

S0L0RR[2:0]

Signal Routing

Description

000

Default setting:

SCI0 connects to LINPHY0, interface internal only

001

Direct control setting:

LP0DR[LPDR1] register bit controls LPTXD0, interface internal
only

100

Probe setting:

SCI0 connects to LINPHY0, interface accessible on 2 external pins

110

Conformance test setting:

Interface opened and all 4 signals routed externally

 


 

 

Summary of Contents for MC9S12ZVM series


























































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands