Freefly MoVI Page 9 User Manual Download

Page: 9 / 30

TRANSMITTER BATTERY LEVEL: The state of charge of the MōVI Controller battery. See Power section for details on what batteries can be

used with the MōVI Controller.

MENU DESCRIPTION: A brief description of each menu accessible from the Home menu.

SCROLL BAR: The scroll bar always appears on the left side of the display and shows the current scroll position, indicating if

there are more menu items above or below the ones currently displayed.

MENU ITEM DETAILS: Within a menu, details for each menu item are shown on the right side of the display. These include status

indicators and bar graphs for menu items that are read-only, and adjustable values or options for menu items

that can be modified. Use the Menu Set Knob to change values or select options where applicable. Refer to the

individual menu descriptions in the Menu Structure section for details on each menu item.

MENU LIST: A list of menu items. The highest-level menus appear on the Home menu. Individual menu items appear within

their respective menu. Scroll through and select a menu item using the Menu Select Knob.

OME

CREEN

YPICAL

ENU

CREEN

Summary of Contents for MoVI































Search results

Summary of Contents for MoVI

Reviews:

Related manuals for MoVI

Brands by name

Popular brands

Freefly MoVI, User Manual

Search results

Summary of Contents for MoVI

Reviews:

Related manuals for MoVI

Brands by name

Popular brands