background image

 

ADS-B FDL-DB Dual Band Series 

Installation Manual 

Document No. 88552 Rev A 

 

FFS Copyright © 2020 All rights reserved. 

4-3 

 

SECTION 4

 

SERIAL INTERFACE SPECIFICATIONS

 

Two data formats may be selected to accept input from external Altitude sensors: 

 

Encoder Altitude

 

– Gray-code to serial altitude converters, etc.

 

 

Air Data Computer

 

– To select a data format, refer to Section 5.1.

 

4.1

 

Altitude Encoder Format 

The Altitude Encoder (aka “Icarus”) data format accepts messages with the following 
parameters: 

Baud:   

9600 

Parity:  

None 

Start Bit:  

Data Bits:  

Stop Bit:  

Update Rate:  

1 msg/sec 

Compatible devices include Rosetta Encoders and Serializers (ARS 50 and ARS 100). The 
compatible format for altitude information is the following 10 byte ASCII message: 

B

yte 

Contents 

 

c/r 

Some examples include:  

'ALT 00000'    

0 feet 

'ALT -1200'  

 

-1200 feet 

'ALT 62505'    

62,505 feet 

'ALT 05604'    

5,604 feet 

4.2

 

Air Data Computer/Sensor Format 

The ADC format accepts messages with the following parameters: 

Baud:   

9600 (default minimum) 

Parity:  

None 

Start Bit:  

Data Bits:  

Stop Bit:  

Update Rate:

  1

 msg/sec 

Air Data messages are accepted when the serial port is set to "ENCODER.” A packet consists 
of a set of ASCII message strings. The first character of each packet is an ASCII Start-of-Text 
(STX = 02H). The last character of each packet will be an ASCII End-of-Text (ETX = 03H). Each 
message string begins with one ASCII character to identify it as an Air Data message ("Z"). The 
second character identifies which message it is. The rest of the string consists of one or more 
alphanumeric ASCII fields. Each message field ends with a carriage return, line feed (CR = 
0D0AH). All numeric fields are ASCII decimal, right justified and zero filled. If the ADC cannot 

Summary of Contents for ADS-B FDL-DB Dual Band Series


































































































































Reviews: