manualshive.com logo in svg

FRC Turbofoam TFC100, User Manual

Share
Download
FRC Turbofoam TFC100 User Manual Download Page 67

TFC100 Rev180215

67

12-Pin Connector/Cable

Pin/Wire 

Description

1/Red  

Supply Power 12/24 VDC

2/Black 

Supply Ground

3/Red  

N/A

4/White N/A

5/Black N/A

6/Red  

N/A

7/White 

FRC Datalink (+)

8/Green 

FRC Datalink (–)

9/Black N/A

10/Red N/A

11   N/A

12   N/A

Optional Remote Control Module

Figure W10.  Optional Remote Control Module Wiring 

NOTE

: For either the TFC100 or TFC200/300/400—

Connect pin 7 and pin 8 to the primary control module

Remote Control Module 

TFC200/300/400

 Rear View

DC 

Power

FRC 

Datalink 

Cable

FRC 

Datalink 

Cable

Remote Control Module 

TFC100

DC 

Power

USB

Access 

Port

*

USB

Access 

Port

*

*NOTE: 

If opened, USB access port plug must be 

tightened to a torque of 8-10 in-lbs. Exceeding this torque 

value can result in damage to its water seal capability.

  

Warning: Flange may not fully bottom out.

Summary of Contents for Turbofoam TFC100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands