manualshive.com logo in svg

FRC Turbofoam TFC100, User Manual

Share
Download
FRC Turbofoam TFC100 User Manual Download Page 6

TFC100 Rev180215

6

Features

Table 1.  TurboFoam Standard Components and Options

Notes:

1  The manual ABF selector option includes two 3/4" foam tank check valves.

2  The standard control module is factory set with the A foam program active.

MODEL

TFC1

16

TFC121

TFC126

TFC135

TFC150

TFC162

TFC165

TFC216

TFC221

TFC226

TFC235

TFC250

TFC262

TFC265

TFC316

TFC321

TFC326

TFC335

TFC350

TFC362

TFC365

TFC416

TFC426

TFC435

TFC450

TFC462

TFC465

Manual ABF Selector

–

–

–

–

–

–

–

O O O O O O O

–

–

–

–

–

–

–

–

–

–

–

–

–

Electric ABF Selector

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

– S S S S S S

Flow Sensor with Mount

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Foam Tank Check Valve 3/4"

S S S –

–

–

– S S S –

–

–

–

– S –

–

–

–

–

–

–

–

–

–

–

Foam Tank Check Valves 1"

O O O

S S S S

O O O

S S S S S

O

S S S S S S S S S S S

Foam Pump Input Strainer 3/4"

S S S –

–

–

– S S S –

–

–

–

– S –

–

–

–

–

–

–

–

–

–

–

Foam Pump Input Strainer 1"

O O O

S S S S

O O O

S S S S S

O

S S S S S S S S S S S

Check Valve Injector 1/2"

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Flush Line Strainer 1/2"

O O O O O O O O O O O O O O

S S S S S S S S S S S S S

Flush Line Check Valve 1/2"

O O O O O O O O O O O O O O

S S S S S S S S S S S S S

Electric Flush Valve

O O O O O O O O O O O O O O

S S S S S S S –

–

–

–

–

–

Summing Box

–

–

–

–

–

–

–

O O O O O O O O O O O O O O O O O O O O

Discharge Check Valve Assy

O O O O O O O O O O O O O O O O O O O O O O O O O O O

Discharge Check Valve Assy 

with Flow Sensor Mount

O O O O O O O O O O O O O O O O O O O O O O O O O O O

Remote ON/OFF Switch

O O O O O O O O O O O O O O O O O O O O O O O O O O O

Tank Float Switch

O O O O O O O O O O O O O O O O O O O O O O O O O O O

BSP Fittings

O O O O O O O O O O O O O O O O O O O O O O O O O O O

B Foam Program Active

O O O O O O O O O O O O O O O O O O O O O O O O O O O

Automatic Foam Proportioning
Class A and Class B Foam
Push Button Control
Preset Foam Percent Button
Single and Dual Foam Tank Systems
Foam Tank Low and Empty Warnings
Time Left to Tank Empty (w/TankVision Pro Only)
Pump Pressure Relief Valve
Flow Totaling for Foam Concentrate and Water
Pre-Programmed Values for Power-Up
Manual Mode

USB Port Interface
Over 30 Programmable Codes
Service Reminders
CAFS Valve Control Signal
Flush Button (TFC300/400 Only)
A/B Selector Button (TFC400 Only)
Remote ON/OFF Switch (Option)
Electric Flush Valve and Panel Button (Option)
Multiple Discharge Sensors w/Summing Box (Option)
Remote Control Head (Optional)

Summary of Contents for Turbofoam TFC100

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands