FRC Turbofoam TFC100 User Manual Download Page 41

Page: 41 / 88

TFC100 Rev180215

Figure L1. TFC Control Module Mounting Dimensions

INSTALLATION

After the system components are installed perform the Operational Test. (Refer to Calibration, Maintenance,

and Troubleshooting Section, Operational Test.) The flow sensor and concentrate pump must be calibrated after

the Operational Test and before normal system operations.

Install Control Module

Note:

The TFC100 model requires a 3 3/4" diameter panel cutout, the TFC200/300/400 models require

a 4 3/8" diameter panel cutout.

1. Measure and mark mounting location for control module panel cutout and mounting screw holes. Make

sure there is clearance behind the panel before cutting holes. Refer to figure for layout and dimensions.

2.  Cut a hole in the panel (check model and dimension) and drill four holes for 10-32 mounting screws.
3.  Place the control module in position and secure with four screws.
4.  Connect the cable(s) to the module. (Refer to Wiring Section.)

Note:

The standard single tank control module is factory programmed for class A foam and must be

reprogrammed if used for class B foam (refer to program code P312).

Mounting holes are

clearance or tapped for

10-32 screws.

3 3/4"

Diameter

3 1/2"

Panel

Cutout

4 1/4"

1 7/8"

3 3/4"

4 3/8"

Diameter

3 3/4"

Panel

Cutout

4 7/8"

2 1/4"

4 3/8"

TFC100

TFC200/300/400

Summary of Contents for Turbofoam TFC100

























































































Search results

Summary of Contents for Turbofoam TFC100

Reviews:

Brands by name

Popular brands

FRC Turbofoam TFC100, User Manual

Search results

Summary of Contents for Turbofoam TFC100

Reviews:

Brands by name

Popular brands