manualshive.com logo in svg

FRC TCA200, Manual

Share
Download
FRC TCA200 Manual Download Page 28

TCA200 Rev171031

28

Figure 8.  DDEC III ECU Wiring TCA202-A00

Vehicle Interface 

Harness Connector

12-Pin 

Connector 

(Refer to 

Figure 4)

Red Wire

Black Wire

C-2
C-1

8-Pin 

Connector 

(Refer to 

Figure 4)

Pin 7 

Signal Return

Pin 6 

Throttle Signal

Pin 8  +5 VDC Reference

Sensor Return

Variable Speed Governor

Sensor Supply (5VDC)

C-3

D-1

A-3

952

510

916

900

901

DDEC

®

III

J1587 Datalink (+)

J1587 Datalink (–)

ECU

Detroit Diesel ECU Connections

Interface Information for DDEC III 1998 engines and older (TCA202-A00)

Connect the Engine Control extension cable to the Variable Speed Governor input 

on the engine ECU. There may be a 3-pin Packard connector (Variable Speed Governor 

Harness Connector installed by the chassis manufacturer) located behind the pump 

panel to plug into for the ECU connections.

Note:

 J1587 Datalink connections are available on the 9-Pin diagnostics 

connector. Refer to Figure 7.  Common OEM 9-Pin Diagnostic Connector.

Summary of Contents for TCA200

































Reviews:

No comments

Brands by name

Popular brands

Load more brands