manualshive.com logo in svg

FRC PumpBoss PBA100, Preliminary Document

Share
Download
FRC PumpBoss PBA100 Preliminary Document Download Page 6

PBA100 Rev0305PreLim

6

PRELIMINAR

Y

 DOCUMENT

FOR REFERENCE/REVIEW

 ONL

Y

GENERAL DESCRIPTION

The PumpBoss pressure governors are compatible with the following engines:

PBA101

Cummins IS Series

PBA102

Detroit Diesel

PBA104

Navistar

PBA105

Caterpillar

PBA106*

Ford

PBA107

Mack

PBA108

Scania

PBA109*

GMC

PBA110

Mercedes

* Note: An adapter and cable assembly replaces the basic 8-pin cable when

connecting the to a Ford 6.0 or GMC engine. These engines may also
require seperate engine coolant and oil pressure sensors.

 Components

The information available on the J1939 databus varies depending on the particular

engine type. Not all wires are used for all engines. Refer to the engine specific wiring
diagram for interface connections. The sensors (if any) that need to be installed will
also vary depending on the engine.

The PumpBoss consist of the following components:

Contol Panel

Pressure Sensor

Engine Coolant Temperature Sensor (As Necessary)

Engine Oil Pressure Sensor (As Necessary)

Transmission Temperature Sensor (Optional)

Cables

Summary of Contents for PumpBoss PBA100






























Reviews:

No comments

Brands by name

Popular brands

Load more brands