manualshive.com logo in svg

FRC BRYTTE DAY OPA740, Manual

Share
Download
FRC BRYTTE DAY OPA740 Manual Download Page 11

OPA740 Rev1108

11

Emergency Back Up Mode

When programmed for the Emergency Back Up Mode the Power Pack monitors 

the facility power via the AC charging cord. If AC power is lost the BrytteDay light 

automatically comes on. When AC power is restored, the BrytteDay light goes off and 

the Power Pack reverts back to monitor and charge mode.

1.  Set up the BrytteDay and connect the AC power. (Refer to Assemble Section.). 

The 

CHARGING

 LED comes on.

2.  To set the emergency back up mode, press and hold the 

ON/OFF

 button until 

the red 

LOW

 LED comes on. Release the 

ON/OFF

 button.

  Results: The amber 

MED

 and green 

FULL

 LEDs alternately blink indicating  

the emergency back up mode is activated.

In this mode the light operates normally:

  Press the 

ON/OFF

 button, the green LED is on and the 

CHARGING

 LED is 

on. The lamphead light comes on.

  Press the 

ON/OFF

 button again, the green LED and the lamphead light go 

off.

When AC power is lost:

  The lamphead light automatically comes on. The 

CHARGING

 LED goes off 

and the 

DISCHARGING

 LED comes on. The amber 

MED

 and green 

FULL

 

LEDs continue to alternately blink.

When AC power is restored:

  The lamphead light automatically goes off. The 

DISCHARGING

 LED goes 

off and the 

CHARGING

 LED comes on. The amber 

MED

 and green 

FULL

 

LEDs continue to alternately blink.

3.  To exit the emergency back up mode, press and hold the 

ON/OFF

 button until 

the red 

LOW

 LED comes on. Release the 

ON/OFF

 button.

  Results: The amber 

MED

 and green 

FULL

 LEDs stop blinking indicating 

the emergency back up mode is de-activated and the normal operating mode 

resumes. 

Summary of Contents for BRYTTE DAY OPA740
















Reviews:

No comments

Brands by name

Popular brands

Load more brands