background image

FOOD WASTE DISPOSER  
FRANKE TURBO PLUS OWNERS GUIDE

Important

 - Read all instructions thoroughly

Please retain for future reference

1.

  Read all instructions before using the appliance.

2.

   To reduce the risk of injury, close supervision is necessary 

when an appliance is used near children.

3.

   Do not put fingers or hands into a waste disposer while it  

is functioning.

4.

   Turn the power switch to the off position before attempting  

to clear a jam or remove an object from the disposer.

5.

   When attempting to loosen a jam in a waste disposer,  

use a long wooden utensil e.g. spoon.

6.

   When attempting to remove objects from a disposer, use 

long-handled tongs or pliers.

7.

  To reduce the risk of injury please note:

 

-  this disposer is not for grinding hard materials, such as  

glass and metal;

 

-  this disposer must be connected to the electric supply by 

means of either a power supply cord or insulated wires in a 
flexible conduit;

 

-  when installing the disposer, care must be taken to ensure  

that the reset button of the overload protection device 
remains readily accessible.

8.

  Additionally for continuous feed models:

 

-  Care must be taken to ensure that the supply is  

disconnected by switching off the electric supply or by 
removing the plug from the socket-outlet before freeing a 
jammed rotor. 

 

-  When not operating the disposer, leave the stopper in place 

to reduce the risk of objects falling into the disposer.

 - 

Do not operate disposer unless splash guard is in place.

9.

  

For proper electrical earth instructions see the  

 

ELECTRICAL CONNECTION details of this manual.

 

10.

   All installations should be carried out by a qualified electrician.

11.

  The symbol       on the product or on its packaging indicates 

that this product may not be treated as household waste. 
Instead, it shall be handed over to the applicable environmental 
collection point for the recycling of electrical and electronic 
equipment. For more detailed information about recycling of 
this  product, please contact your local authority, your 
household waste disposal service or the shop where you 
purchased the product.

ImPORTANT SAFETy INSTRuCTIONS

Instructions pertaining to risk of fire, electric shock or injury to persons.
Save these instructions.

WARNING

 - When using electrical appliances, basic precautions should always be 

followed, including the following:

www.franke.co.uk

Summary of Contents for TURBO PLUS









Reviews: