background image

tHe installation

ProCeDUre

installing tHe omni DUo kitCHen taP 

Carrying out this operation first will make it easier to plan the 

layout inside the cabinet. For safety it is advisable to locate the 
tap out of the reach of smaller children. 

1.  The tap will require a standard 35mm diameter hole drilled in 

the kitchen work surface. 

important note:

 before cutting the 

hole make sure that there is sufficient clearance between the 

tap handle and the back splash when the handle is in the fully 
open position.

2.  Insert the flexible hoses and the wire lead through the 35mm 

hole.

3.  Position the tap for the owners’ convenience. (The tap can 

be rotated 180° for left handed operation of the boiling water 
function).

4.  Working inside the cabinet, slide the gasket (8) and the 

clamp plate (5) over the hoses and the stud at the base of 
the tap. Screw the clamp nut (6) on to the stud using the box 
spanner (7). 

5.  Check the alignment of the tap then tighten the clamp nut 

using the box spanner to firmly secure it on the work surface.

Plan the layout inside the cabinet

•  Determine the best positions for the boiler and the filter unit, 

making sure that the boiler power cable, the flexible hoses, 
and the filter cartridge change indicator cable, are all within 

comfortable reach of their respective connection points without 
them being compressed, stretched or kinked. 

•  The boiler must be installed upright with the hose connections at 

the top, never on its side. 

•  Allow a minimum clearance of 80mm at the top of the boiler for 

the connecting hoses. 

•  Choose a location for the filter unit (20) and the stop valve (23) 

to allow convenient access for  future filter cartridge changes. 

Summary of Contents for omni DUO

















Reviews: