Framery Q Working with PAL Installation Instructions Manual Download Page 55

Page: 55 / 106

10 Install the electrical equipment

10.1 Install the power cord from the floor

If installing the power cord from the floor, follow these instructions. If you intend to install

the power cord from the roof, see

Install the power cord from the roof

on page 57.

Choose which side of the floor you want to install the power cord to. The following

instructions show installation from the right-hand side.

Unscrew the 4x30 screw (1 pcs) and remove the cover plate at the foot of the right side

wall. Set the screw and cover plate aside.

Framery Q Working with PAL Installation instructions
[email protected]

Summary of Contents for Q Working with PAL











































































































Search results

Summary of Contents for Q Working with PAL

Reviews:

Related manuals for Q Working with PAL

Brands by name

Popular brands

Framery Q Working with PAL, Installation Instructions Manual

Search results

Summary of Contents for Q Working with PAL

Reviews:

Related manuals for Q Working with PAL

Brands by name

Popular brands