3
Install Memory
4. The clips at both ends of the socket will
snap into place when the memory module
is securely inserted.
3. Place the memory module onto the
socket, then push it down firmly and
seat it vertically into the memory
socket.
1. Spread the clips at both ends of the
memory socket.
2. Memory module has asymmetric pin
counts in its two sides separated by a
notch in the middle, so it can only fit in
one direction.
4
Install Hard Disk Drive (HDD)
1. Put the HDD into the chassis as depicted
in the picture.
3. Fasten the HDD with three screws.
2. Move the HDD to align with three
screw holes.
4. Use provided shorter SATA cable to
connect motherboard and HDD.
5. Connect power cable to HDD.
Chassis Quick Installation
SFF R10-S2
WEEE:
The use of this symbol indicates that this product may not be treated as household waste. By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your local city office, your household waste disposal
service or the shop where you purchased this product.
All image are for reference only, please refer to the physical chassis for specific features.
SPECIFICATION
M/B Configuration
Mini ITX MB
Dimension (W/H/D)
283*282*95 (mm)
Drive Bays
1*5.25" External
1*3.5" External
1*3.5" Internal
Front I/O Ports
2*USB2.0
1* Micphone,
1*Earphone
SPS
TFX 150W
Fan
80*80*20mm
3. Remove the top cover by pushing it toward
real panel, and lift it.
4. Check there are motherboard, power
supply and driver bay inside.
2. Remove the top cover screw on the
real panel.
1.
Take the chassis out of its packing.
Top cover
Front
Panel
Top cover (or Side Panel)
1
Open the case
2
Remove Bezel and Driver Bay
1.
Release four clips on the bezel top.
2.
Hold the bezel with both hands, lift
left hand side to release two bottom
clips.
3.
Lift right hand side to release another
bottom clip.
4.
Remove two screws to detach
the driver bay.
5. Push driver bay toward real panel and lift it
to remove.
6.
Now, you can start the installations of
memory, hard drive and optical disk drive.
*
Bezel View
USB Port
USB
接口
USB
埠
USB
ポット
USB
포트
USB-Anschluss
Puerto de USB
Port USB
USB Bağlantı Noktası
Porta USB
Porta USB
Порт USB
Port USB
USB csatlakozó
Reset Button
重启按钮
重啟開關
リセットボタン
재설정 버튼
Reset-Taste
Botón de reinicio
Bouton de remise
Sıfırlama Düğmesi
Tasto Reset(Ripristino)
Botão Reiniciar
Кнопка Reset
przycisk resetowania
Alaphelyzet gomb
Power Button
电源开关
電源開關
パワーボタン
전원 버튼
Power-Taste
Botón de encendido
Bouton de puissance
Güç Düğmesi
Tasto Power
Botão Alimentação
Кнопка питания
przycisk zasilania
Üzemkapcsoló gomb
Line Out
音频输出端口
音源輸出
ラインアウト
라인 출력
Line-Ausgang
linea de Salida
Sortie ligne
HatÇıkışı
Uscita linea
Saída de linha
Линейный выход
wyjście liniowe
Vonalszintű kimenet
Microphone In
音频输入端口
音源輸入
マイク入力
마이크 입력
Mikrofon-Eingang
Entrada de micrófono
Entrée microphone
Mikrofon Girişi
Ingresso microfono
Entrada microfone
Вход микрофона
wejście mikrofonu
Mikrofon bemenet
Optical Disk Drive
光驱
光碟機
光学ディスクドライブ
옵티컬 디스크 드라이브
Optisches Laufwerk
Unidad de disco Optico
l’unité de disques optique
Mikrofon Girişi Optik Disk Sürücü
unità disco ottico
Drive do disco óptico
Оптический привод
stacja dysków optycznych
Optikai lemezmeghajtó
*
Rear Panel View
Rear I/O
后面板接口
後面板
リア
I/O
후면
I/O
Rückwärtige I/O
I/O trasero
Rear I/O
Arka G/Ç
I/O posteriore
E/S de trás
Вход/выход задней панели
tylne wejście/wyjście (I/O)
Hátsó I/O csatlakozók
Power Cord Input
电源接口
電源輸入
電源コード入力
전원 코드 입력
Stromkabel Eingang
Cable de alimentación de entrada
Cordon d’alimentation d’entrée
Güç Kablosu Girişi
ingresso cavo d’alimentazione
Entrada do cabo de alimentação
Вход штура питания
wejście kabla zasilającego
Tápkábel bemenet
P/N: 3A250J000-000-G
Small Form Factor Barebone