FOTEK GD20-004G-2 Operation Manual Download

Page: 18 / 171

Goodrive20 Series VFD

Installation guidelines

-13-

Chapter 3 Installation guidelines

The chapter describes the mechanical installation and electric installation of the VFD.



Only qualified electricians are allowed to carry out what described in this

chapter. Please operate as the instructions in Chapter 1 "Safety

precautions". Ignoring these may cause physical injury or death or

damage to the devices.



Ensure the power supply of the VFD is disconnected during the operation.

Wait for at least the time designated after the disconnection if the power

supply is applied.



The installation and design of the VFD should be complied with the

requirement of the local laws and regulations in the installation site. If the

installation infringes the requirement, our company will exempt from any

responsibility. Additionally, if users do not comply with the suggestion,

some damage beyond the assured maintenance range may occur.

3.1 Mechanical installation

3.1.1 Installation environment

The installation environment is the safeguard for a full performance and long-term stable
functions of the VFD. Check the installation environment as follows:

Environment

Conditions

Installation site Indoor

Environment

temperature



-10°C

–+50°C, and the temperature changing rate is less than

0.5°C/minute.



If the ambient temperature of the VFD is above 40°C, derate 1% for every

additional 1°C.



It is not recommended to use the VFD if the ambient temperature is above

50°C.



In order to improve the reliability of the device, do not use the VFD if the

ambient temperature changes frequently.



Please provide cooling fan or air conditioner to control the internal

ambient temperature below the required one if the VFD is used in a close

space such as in the control cabinet.



When the temperature is too low, if the VFD needs to restart to run after a

long stop, it is necessary to provide an external heating device to increase

the internal temperature; otherwise, damage to the devices may occur.

Humidity



RH≤90%



No condensation is allowed.

Summary of Contents for GD20-004G-2












































































































































































Search results

Summary of Contents for GD20-004G-2

Reviews:

Related manuals for GD20-004G-2

Brands by name

Popular brands

FOTEK GD20-004G-2, Operation Manual

Search results

Summary of Contents for GD20-004G-2

Reviews:

Related manuals for GD20-004G-2

Brands by name

Popular brands