fos4X Blackbird OECD MDE1195 Instructions For Use Manual Download Page 45

Page: 45 / 76

5. Installation

Installation

Observe the safety instructions. See

Safety, page 9

5.1

Important Safety Notes for Installation

NOTICE

Damage to the fiber-optical cables.

Too small bending radii and kinks can irreparably damage the
fibers in fiber-optical cables.

Observe the min. bending radii of the cable. See technical
data of the cable.

Do not kink or squeeze fiber-optical cables.

5.2 Attaching the Measuring Device in the Control Cabinet

Conditions:

■

Control cabinet with sufficient space for installation. See

Dimensions, page 17

■

Control cabinet with permissible environmental conditions. See

Environmental

Conditions, page 15

Attaching the measuring device in the control cabinet:

Attach the measuring device with 4x M6 screws and nuts.

TIP

Control cabinets from fos4X provide 4 welding studs to attach
the measuring device with 4 x M6 nuts.

5.3 Connecting the Interfaces

Figure 19: ETH
connector

Connecting the Ethernet Interface:

Connect a RJ45 cable to the ETH connector.

MDE1195_4-10_1.3.x_5.0_Blackbird

OECD_(9CH, PRN)-en-us

45 / 76

Summary of Contents for Blackbird OECD MDE1195













































































Search results

Summary of Contents for Blackbird OECD MDE1195

Reviews:

Brands by name

Popular brands

fos4X Blackbird OECD MDE1195, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE1195

Reviews:

Brands by name

Popular brands