fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 76

Page: 76 / 80

10. Taking out of Service and Disposal

Remove 4x M6 screws or nuts. Mounting depends on the installation. See

Attaching the Measuring Device in the Control Cabinet, page 50

Remove the Blackbird OECD from the control cabinet.

Pack the Blackbird OECD. See

Packing, page 48

10.2 Disassembly

The product may only be disassembled by fos4X or a specialized disposal company.

10.3 Disposal

NOTICE

Risk to the environment due to incorrect disposal of the
product.

Improper disposal of the product may cause damage to the
environment.

Observe applicable environmental regulations.

The Blackbird OECD is an electrical appliance and must not be
disposed of with household waste.

Disposing of the Blackbird OECD:

Contact fos4X Support for take-back. See

fos4X Support,

page 73

76 / 80

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands