fos4X Blackbird OECD MDE0835 Instructions For Use Manual Download Page 72

Page: 72 / 80

9. Maintenance

Connect the PC to the ETH connector.

Open the software fos4X Firmware Flasher (f3.exe).

The page FOS4X FIRMWARE FLASHER is displayed.

Figure 34: fos4X Firmware Flasher

Select the network adapter in

Network Interface

Detected measurement devices are displayed in

Available Devices

If the Blackbird OECD is not displayed:

Make sure that the PC is connected to the ETH port of the Blackbird OECD.

Make sure that the correct network adapter is selected.

Make sure that the IPv6 protocol is enabled on the PC.

Make sure that the PC has a valid IPv6 link local address.

Click on

Network Interface

Click on

Firmware Archive

Select the firmware archive.

Click on OPEN.

The firmware archive is displayed in the

Firmware Archive

field.

72 / 80

MDE0835_4-10_1.3.x_5.0_Blackbird

OECD_(6CH, CNO)-en-us

Summary of Contents for Blackbird OECD MDE0835

















































































Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands

fos4X Blackbird OECD MDE0835, Instructions For Use Manual

Search results

Summary of Contents for Blackbird OECD MDE0835

Reviews:

Related manuals for Blackbird OECD MDE0835

Brands by name

Popular brands