Forum SDL-100/1, Operation Manual

Page: 12 / 50

WARNRNG
a d
o never unlatch
/
open the tool while a pipe is
suspended in the tool
;
the pipe will be lost
!
WARNRNG
a w
hile using the elevator
,
always make sure the
door is completely closed with the latch
/
latch lock fully engaged
and if applicable the verification pin properly installed
.
WARNRNG a p
ay special
a
ttention to the verification pin
(
if
applicable
),
latch and latch lock for any signs of wear
,
bending
or damage at any time
.
in case parts are damaged or bent
,
replace
immediatelly by new
,
original parts
.
WARNRNG a t
he lifting of vertical pipes is to be performed
carefully and must be monitored
. t
he picking up of horizontal or
tilted pipes is dangerous and not permitted by the manufacturer
.
WARNRNG a i
f the operator considers to use the elevator
for other operations than the intended use
(
for example handling
of horizontal pipes
),
it is mandatory to make an additional risk
analysis
.
WARNRNG
a h
andles
/
grip points are marked by green paint
.
d
uring operations these grips are the only places the tool can be
handled safely
. i
n all
non-
green marked places there is a risk
for injury
. a
utomatic
/
remote operated tools may not have any
green painted grip
-
points
. i
n this case it is not allowed to touch
the tool while operating
.
XIV Safety Signs
Fig. 2: Warning sign PN 671638
General warning
Fig. 3: Warning sign PN 671642
Apply grease
Fig. 4: Warning sign PN 611524
Do not touch.
Fig. 5: Warning sign
PN 671640-1
Do not place your
hands between
moving parts.
Fig. 6: Warning sign
PN 671641
Risk of crushing.
12
SDL PN: 651520-Y-BC-D - Revision: 10 04-2016
Operating Instructions
XIII General Warnings
WARNRNG
a o
ne should avoid creating ignition sources
,
like heat
,
as a result of the use of the tool with other tools or
equipment
.
WARNRNG a d
o not use the tool for any other purpose
than given in this document within it
`
s specification
.
WARNRNG a f
ailure to conduct routine maintenance could
result in equipment damage or injury to personnel
.
WARNRNG a w
ear personal protection equipment while
working with the equipment
.
WARNRNG
a i
f any safety elements
(
like safety ropes
,
safety sheets
,
plates or washers
)
were disassembled due to
maintenance work
,
do
not
re
-
use them
. a
lways replace them
with new safety elements
.
WARNRNG a a
ll warning plates
,
signs and labels attached
to the equipment must be observed
. t
he warning plates
,
signs and
labels must be present on the tool
. d
o not remove the labels
. i
f
they are missing
,
replacing is mandatory
.
WARNRNG a a
ny modification to the tool carried out
without the approval of
f
orum
b+v o
il
t
ools
g
mb
h
will void
any warranty
.
WARNRNG a u
sing the tool with damaged or worn parts
can create serious incidents
.
WARNRNG
a t
he company operating the tool is responsible
for evaluating safe and proper use of the tool in a hazard
analysis
.
WARNRNG a i
t is not allowed to use any components
which are of
"
non
-f
orum
b + v o
il
t
ools
"
origine
,
or use
"
non
-oem"
parts which are not approved by
f
orum
b+v o
il
t
ools
g
mb
h. i
t will void any warranty and
may effect the correct functioning of the tool and it
'
s safety
features
.
WARNRNG a t
he operating company is obligated to issue
working instructions for safe use and supervise observance of
these working instructions
.
WARNRNG a e
very
e
mployee
,
which operates
,
services
,
inspects or otherwise involved with the use of the tool in other
areas has to ensure
,
that these actions are done by trained and
by an
f
orum
b+v o
il
t
ools
g
mb
h
authorized personnel
,
WARNRNG
a
and should complete regular courses of
training
,
to ensure proper use as well as safe operation
,
correct
maintainance and inspection
.
WARNRNG a i
f necessary
,
a reasonable
,
additional
supervisor should be appointed during operation
.
WARNRNG a s
tay away from the tool during operation
.
i
n case it is remote operated it may make movements without
warning
.