Fortress Automotive Security FS-90 Installation Handbook Download Page 1 | Manualshive

Page: 1 / 41

Fortress Automotive Security FS-90 Installation Handbook Download Page 1

FS-60 FS-80 FS-90 Alarm Combo System

INSTALLATION HANDBOOK:

INTRODUCTION

Congratulations on your choice of a Crimestopper combination alarm & remote engine starter with animated 3D
graphics.

This  installation  book  is  designed  for  the  installer  or  individual  with  an  existing  understanding  of
automotive electrical systems, along with the ability to test and connect wires for proper operation.  To ease
installation,  we  suggest  that  you  READ  THIS  MANUAL  before  beginning  your  installation.    This  book  is
provided as a GENERAL GUIDELINE and the information contained herein may differ from your vehicle.

DISCLAIMER:
Crimestopper Security Products, Inc. and its vendors shall not be liable for any accident resulting from the
use of this product. This system is designed to be professionally installed into a vehicle in which all
systems and associated components are in perfect working condition.

TECHNICAL SUPPORT (800)-998-6880
Monday - Friday 8:00am - 4:30pm Pacific Time

Website: www.crimestopper.com

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET
SIMI VALLEY, CA. 93063

REV E 07.2010

1
2
3
...
»

Summary of Contents for FS-90










































Reviews:

No comments