background image

Generating SNMP traps for shelf manager system events

Using the shelf manager CLI

FortiGate-5140B Chassis Guide

68

01-500-156415-20151104

http://docs.fortinet.com/

 

4

Enter the following command to re-activate this PEM:

# clia activate 20 7

When activating again the PEM B, there are three state changes (

M1 -> M2 -> M3 -

> M4

) and three traps sent.

SNMP trap details

The trap below could be sent when PEM B state changes from M4 to M6. The important 
trap fields are the specific trap field (

in red below

) and the variable bindings fields (

in 

blue

). Byte 2 of the specific trap field shows the sensor type (f0 = hot swap) and the 4th 

byte is the event offset (06 = assertion to state 6= M6).

The variable bindings fields which are in bold in the trace below are the following bytes:

Byte 26 = Event Source Type = Class of device or type of software that originated the 
event

Byte 27 = Event Severity

Byte 28 = Sensor Device byte = Identifies the instance of the device that holds the 
sensor that generated the event

Byte 29 = Sensor Number

Sensor number 9 is the hot swap sensor for PEM B:

# clia sensor 20 9

20: LUN: 0, Sensor # 9 ("FRU 7 HOT_SWAP")

Type: Discrete (0x6f), "Hot Swap" (0xf0)

Belongs to entity: (0xa, 97) [FRU # 7]

No. Time 

Source 

Destination 

Protocol 

Info

1  17:11:21.469567 192.168.181.66 192.168.182.86 

SNMP 

trap

Frame 1 (177 bytes on wire, 177 bytes captured)

Ethernet II, Src: RapidCit_5f:cc:97 (00:e0:16:5f:cc:97), Dst: 

Vmware_3c:55:c0 (00:0c:29:3c:55:c0)

Destination: Vmware_3c:55:c0 (00:0c:29:3c:55:c0)

Source: RapidCit_5f:cc:97 (00:e0:16:5f:cc:97)

Type: IP (0x0800)

Internet Protocol, Src: 192.168.181.66 (192.168.181.66), Dst: 

192.168.182.86 (192.168.182.86)

User Datagram Protocol, Src Port: 1024 (1024), Dst Port: 

snmptrap (162)

Simple Network Management Protocol

version: version-1 (0)

community: public

data: trap (4)

trap

enterprise: 1.3.6.1.4.1.3183.1.1 (SNMPv2-

SMI::enterprises.3183.1.1)

agent-addr: internet (0)

internet: 192.168.181.66 (192.168.181.66)

generic-trap: enterpriseSpecific (6)

specific-trap: 15757062

time-stamp: 1975765011

variable-bindings: 1 item

Item

Summary of Contents for FortiGate-5140B

























































































Reviews: