Förster-Technik TAP5-VS2-50 Original Service Manual Download Page 53

Page: 53 / 130

Programming and control

Restoring data

This is how to perform data restoration:

1. Navigate via

> Device data > Data backup

to the

Internal (automatic feeder)

sub-

menu.

2. Confirm

Restore?

by choosing

3. Confirm the security prompt

Restore last backup?

by choosing

A progress bar informs you about the current status of the data restoration being carried out.

Checking the available data backup

Check the data backup as follows:

1. Navigate via

> Device data > Data backup

to the

Internal (automatic feeder)

sub-

menu.

2. In the

last backup

menu, you can view the time and date when the last backup was per-

formed.

4.6.7.2

External data backup using an SD card

During each backup, a folder with the date of the backup is created on the SD card. If

data res-

toration

is required, a date stored on the SD card can be entered and selected using the num-

ber field. The date of the last backup is always shown on the display.

When the feeder is delivered, by default an SD card is fitted in the slot on the hand terminal.
The SD card should remain in the hand terminal at all times.

SD card and hand terminal

Proceed as follows to perform a data backup using an SD card:

1. Open the rubber cover on the right side of your hand terminal.

2. Insert the SD card into its slot.

3. Navigate via

> Device data > Data backup

to the

SD card

sub-menu.

4. Confirm

save?

by choosing

A progress bar informs you about the current status of the data backup being carried out.

Summary of Contents for TAP5-VS2-50



































































































































Search results

Summary of Contents for TAP5-VS2-50

Reviews:

Related manuals for TAP5-VS2-50

Brands by name

Popular brands

Förster-Technik TAP5-VS2-50, Original Service Manual

Search results

Summary of Contents for TAP5-VS2-50

Reviews:

Related manuals for TAP5-VS2-50

Brands by name

Popular brands