Gazebo
Fixing Pack (BFGAZFP)
Not to Scale
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE SCREWDRIVER
STEP LADDER
TAPE MEASURE
HAMMER
Issue 0115
PARTS LIST
Important :
Assembly of this
Gazebo requires a
minimum of three
adults.
Must pre-drill for
each screw used.
IMPORTANT, RETAIN FOR FUTURE REFERENCE; READ
CAREFULLY
Check all parts prior to assembly
This building is pressure treated to ensure the longevity of all
timber components and to protect against rot. This may leave
a colour difference on some parts that will even out as the
moisture content stabilises. This will not require additional
treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Due to the nature of the material the doors may need some
trimming for a neater fit.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
Technical Help line:
0333 7777 089
8.30 am and 5.00
pm Monday to Friday.
In line with your statutory rights, please check all parts prior
to assembly, as assembly of damaged parts may be deemed
to be acceptance and this may affect the remedies you are
entitled to. If the product is not constructed in accordance
with the instructions, or is altered in anyway (e.g. painted) the
manufacturer cannot be held liable for any resulting damage.
flush
BAGFL1 Qty 2
BAGRF Qty 6
BAGFL2 Qty 2
BAGBAL
Qty 2
BAGRF Qty 6
BABGMP
Qty 3
BAAGM Qty 2 BAGPP
Qty 3
Arden Gazebo Parts
Burford Gazebo Parts
A
B
C
E
BAGRAFC Qty 6 BAGPOST
Qty 6
BAGARCH Qty 1
BAGARCH Qty 3
D
C
BAGMETHAT Qty 1
BAGFLCAP
Qty 6
(floor capping)
BAGFINTOP Qty 1
BAGFINB Qty 1
BGLRFB2 Qty 6
(1296mm roof board)
BGLRFB1 Qty 6
(1224mm roof board)
GBSLA
T1075 Qty 3
(
1075mm bench slat)
GBSLA
T952 Qty 3
(952mm bench slat)
GBSLA
T830 Qty 3
(830mm bench slat)
H
Q
I
K
G
L
M
N
J
P
F
O
R
T
GBBRACE Qty 3
(1075mm bench back brace)
GB
FB
RA
CE
Qt
y 3
(73
4m
m
be
nc
h f
ron
t b
rac
e)
GBSBRACE Qty 12
(330mm bench side brace)
GBSUP
Qty 3
(885mm bench support)
GBLEG440 Qty 12
(bench leg)
U
V
W
X
S
3
5
1
4
2
F
G
K
E
J
D
C
flush
Place the floor sections
together to create the base
Position and fix each of the floor capping
pieces around the edge of the base using
4 x 30mm nails for each.
Fix the posts to either side of one of the panels
and fix them to each side using 4 x 70mm screws,
screwing through the panel framework first.
flush
flush
Lip
Make sure that all of the panels are
secured to the posts and are in line with
the outside of the base as shown
(do not fix to the floor at this point)
B
Place the arch
pieces between
the posts so that
they are in line
with the panels.
Fix the arch in
place using 2 x
70 mm screws for
each using the
pre-drilled holes.
Check that all of the sides are flush with the base
before securing each panel to the base using 4 x
70mm screws, screwing down through the framing.
a
b
Silicon Gun and Tube Qty 1
70mm screw Qty 98
45mm screw Qty 138
30mm Nails Qty 24
SPIRIT LEVEL
