8’ x 6’ T & G SHED
Fixing Pack (MTGSH86V2FP)
Not to Scale
REQUIRED TOOLS :
(NOT SUPPLIED)
TAPE MEASURE
HAMMER
Issue 0319
FELT
B
MTGSH86PE
PLAIN END
MTGSH86WS
WINDOW PANEL
MTGSH86PS
PLAIN PANEL
MTGSH86RF
ROOF BOARD
QTY 2
FELT81RED
QTY 1
C
D
E
G
J
F
95180135PPT
135mm LOCK BLOCK
QTY 1
FIN20510012PPT
FINIAL
QTY 2
A
Place the panels on top of the completed floor. Make sure that all the panels are tight and flush before fixing them
to each other using 3x50mm screws.
When the panels are secured to each other, make sure they are square and fix to the floor using 3x50mm screws
for each panel ensuring that the screws are located into the bearers underneath.
MTGSH86 PARTS LIST
4
1
3
MTGSH46FL
FLOOR
QTY 2
MTGSH86DR
DOOR
MTGSH86DE
DOOR END
57121710PPT
1710mm CORNER STRIP
QTY 4
BARGE BOARD
QTY 4
H
O
P
N
H
M
F
Top View
2
B
C
D
C
Shoot Bolt
Cranked Hinge
Qty 2
30mm Screw Qty 28
50mm Screw Qty 27
25mm Screw Qty 18
Ridge Plate
Place the corner strips so that they cover the joins between the
panels. Fix each in place using 3x30mm screws.
IMPORTANT, RETAIN FOR FUTURE REFERENCE;
READ CAREFULLY
This buildings is pressure treated to ensure longevity of all
timber components and to protect against rot. This may
leave a colour difference on some parts that will even out
as the moisture content stabilises. This will not require
additional treatment.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Please keep all plastic bags and small parts away from
children
- The roof of this building is not a load bearing structure.
- This product must be built on a solid level base.
- Please use suitable gloves when handling glass.
Technical Help line:
0333 7777 089
8.30
am
to 5.00
pm Monday to Friday.
Check all parts prior to assembly
In line with your statutory rights, please check all parts
prior to assembly, as assembly of damaged parts may be
deemed to be acceptance and this may affect the
remedies you are entitled to. If the product is not
constructed in accordance with the instructions, or is
altered in anyway (e.g. painted), the manufacturer cannot
be held liable for any resulting damage.
25mm Nail Qty 4
DRIP STRIP
QTY 1
MTGWIN
WINDOW
QTY 2
A
Attention:
Take care
when placing
the screws.
These can
not be
backed out.
Place and secure two hinges to the door so that they line up with the battens on the
reverse, using 25mm
Security Screws
for each.
Place the door into the door end ensuring that the door is square. Fix the doors in place
using 3x25mm
Security
Screws
for the other section of each hinge.
D
M
M
H
Place the acrylic sheet inside the window frame and position the beading so that
each section fits flush and keeps the sheet tight. Fix each piece using 3 x Panel Pins.
L
K
I
12mm Offset
Place and fix the Casement Stay centrally
against the inside of the opening window and
make sure it is offset at least 12mm from the to
top of the frame so as not to hit the acrylic sheet.
Fix in place using 2 x 25mm screws.
Mark the position of the holes of the casement
stay when the window is closed before fixing the
pins in place using the 25mm screws provided.
5
40mm Screw Qty 32
10mm Felt
T
acks
Qty 100
25mm Countersunk
Security Screws Qty 14
Casement Stay Qty 1
25mm Panel Pins Qty 28
Tee Hinge Qty 2
Important : Assembly of
this shed requires a
minimum of two adults.
Must Pre drill for
each screw used.
Escutcheon
Rim Lock
Handle Set
I
XT623502
ACRYLIC SHEET
QTY 2
H
L
H
K
15120508PAII45PT
508mm GLAZING STRIP
QTY 4
15120629PAII45PT
629mm GLAZING STRIP
QTY 4
For the
opening window
fix two cranked hinges to the top of the window so that it
sits in the rebate. Fix the smaller section of the hinge to the window using 2 x 25mm
screws for each. Open up the hinges and fix the remaining section of each hinge to
the top of the window panel using another 3 x 25mm screws for each hinge.
Opening Window
Opening Window
POZI DRIVE
SCREWDRIVER
SHARP KNIFE
FLAT HEAD
SCREWDRIVER
