FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 267

Page: 267 / 285

TIMS MVP™ System Maintenance

TIMS MVP

™

Setup and Configuration Guide 243

TIMS MVP

™

System Maintenance

Scope

This guide describes recommended preventive maintenance to ensure TIMS MVP

™

systems

and TIMS Review stations run as smoothly as possible.

Since TIMS MVP

™

and TIMS Review computers are Windows 10-based computers, preventive

maintenance is typical of any Windows 10 operating system.

Maintenance consists of:

•

checking and optimizing the hard drive

•

verifying disk space

•

deleting older TIMS MVP

™

studies, and

•

cleaning system airflow grills.

Notes

About the TIMS Review Software

TIMS Review software is loaded on site supplied computers. Third party utility programs may be
installed, and menus depicted will differ. Please consult your IT group and the specific program
documentation.

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands