background image

 

WARRANTY 

 

(Effective October 5, 2009) 

 

Forenta  warrants  major  components  (heads,  bucks  and  frames  only)  to  be  free  from  defects  in  materials  or  workmanship, 
which may cause failure under normal usage and intended service for a period of five years from the date of shipment from 
the  factory.  Damages  resulting  from  neglected  maintenance,  abuse(such  as  any  damage  caused  by  pressing  on  metal 
buttons) or improper adjustments not to be considered defects. 
 
Forenta will not accept nor assume any liability resulting in personal injury or property or equipment damages caused by lack 
of  maintenance,  lack  of  attention  to  or  improper  operation  of  this  piece  of  equipment.  Failure  to  adhere  to  maintenance, 
service  and  operational  procedures  as  recommended  in  the  Instruction  Manual  for  this  equipment  will  void  any  and  all 
warranties. 
 
Forenta  further  warrants  all  other  fabricated  components  and  outside  supplier  purchased  components,  used  in  the  original 
manufacture, to be free from defects in materials or workmanship, which may cause failure under normal usage and intended 
service,  for  a  period  of  two  years  from  the  date  of  shipment  from  the  factory  (ordinary  wear,  neglect,  abuse,  accident,  or 
deterioration  due  to  corrosion,  or  breakdown  of  electrical  parts  due  to  high  or  low  voltages,  not  to  be  considered  defects), 
subject to the following conditions: 
  
Forenta  does  not  warranty  service  labor  in  the  replacement  of  parts  covered  under  this  warranty.  In  certain  applications, 
Forenta, at its discretion, recognizing that a defect is present and at an agreed to cost prior to service labor being performed, 
will reimburse a distributor or local service company to repair the defect or replace the defective part. 
 
1.  Expendables  such  as  padding,  covers,  lubricants,  and  discs,  diaphragms  and  O-rings  of  valves  and  cylinders,  and 

decorative or protective trim and paints, are not guaranteed. 

 
2.  Electrical  timers,  motors,  vacuums  and  all  other  electrical  components  from  outside  suppliers  used  in  the  original 

manufacture  of  Forenta  Equipment  carry  the  warranty  of  their  manufacturer  for  120  days  from  date  of  shipment  from 
Forenta.  These  parts  must  be  returned  to  Forenta  under  our  normal  return  authorization  policy  or  serviced  by  a  repair 
shop authorized by the motor manufacturer or Forenta. 

 
3.  The responsibility of Forenta is limited to the furnishing of a replacement part, F.O.B. point of origin. All replacement parts 

will be charged for and credit under this warranty will be issued only if: 

A.  The returned part proves upon examination to have actually been defective of workmanship or materials, and 
B.  The serial number of the machine is supplied along with the part, and 
C.  The returned part has been sent with promptness prepaid to 

                    Forenta, L.P. 
                    2300 W. Andrew Johnson Hwy. 
                    Morristown, TN 37814 USA 
 and received by Forenta within 30 days from shipment of the replacement part. 
 

4.  This warranty does not include freight or handling charges incurred repairing or replacing defective equipment. Forenta is 

not  responsible  for  garments  damaged  on  this  equipment  or  for  any  other  consequential  damages,  loss  or  expenses 
arising  in  connection  with  the  use  of,  or  the  inability  to  use,  its  equipment  for  any  purposes  whatever,  or  for  losses 
sustained by this equipment being out of operation for any reason. Forenta does not warrant any specific production from 
any of its equipment. 

 
5.  This  warranty  shall  not  include  parts  or  equipment  damaged  by  accident,  abuses,  acts  of  God,  acts  of  third  person, 

operation  of  equipment  under  unusual  conditions  or  for  which  it  was  not  represented,  overriding  safety  devices,  or  for 
causes beyond the company’s control. 

 
6.  Since  the  age  of  a  machine  can  only  be  determined  by  the  serial  number,  the  warranty  will  be  voided  in  the  event  of 

mutilation  or  removal  of  the  nameplate  from  the  machine.  Resale  or  movement  of  equipment  from  the  original  point  of 
installation automatically terminates this warranty. 

 
7.  This warranty  is in  lieu of  all other  warranties, expressed or implied,  and is Forenta’s sole  warranty. With respect to the 

equipment,  Forenta  makes  no  other  warranty  of  any  kind  whatever  expressed  or  implied,  and  all  implied  warranties  of 
merchantability and fitness for a particular purpose which exceed the above obligation, are hereby disclaimed by Forenta 
and  excluded.  Forenta  does  not  authorize  any  person  or  corporation  to  increase  the  warranty  as  herein  specified  or  to 
assume for it any other liability. 

 

 

Summary of Contents for 46SVB





















Reviews: