Ford VSS Manual Download Page 26

Page: 26 / 89

INSTALLATION

Vehicle Security System (VSS)

Mustang

NOTICE: Vehicle security systems are only
applicable to vehicles with RKE.

1. Verify correct kit number.

Review VSS Installation Kit Contents

NOTE:

Kits are vehicle specific and are not

interchangeable.

2. Review the VSS kit contents.

VSS System Kit

QUANTITY

DESCRIPTION

MODULE ASSEMBLY

VSS SOFTWARE

CARTRIDGE

ASSEMBLY

WIRING HARNESS

4. Place the software cartridge onto the control

WITH 24-WAY

CONNECTOR

module.

INSTALLATION PARTS

BAG

FUSE PARTS BAG

OPERATORS

INSTRUCTIONS

OPERATORS QUICK

REFERENCE WALLET

CARD

VEHICLE SECURITY

SYSTEM WARNING

WINDOW DECAL

Module Preparation

5. Plug the wiring harness(es) into the module.

3. Place the supplied fuses into the power

•

A - Harness: 24-way, used on all systems.

distribution block on the VSS control module.

•

C- Harness: 16-way, used on all systems

•

Move the polarity jumpers to their proper

incorporating Lot Mode.

locations on the control module, see

illustration.

2013 Mustang

Vehicle Security

Page 1 of 8

SK9L2J-19G364-AA

Summary of Contents for VSS


























































































Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands

Ford VSS, Manual

Search results

Summary of Contents for VSS

Reviews:

Related manuals for VSS

Brands by name

Popular brands