Ford TRANSIT CUSTOM 2012.75 Page 119 Mounting Manual Download

Page: 119 / 184

Mini Relay

Mini Relay Parameters

40 Amps

Normally open contacts

20 Amps

Normally closed contacts

300 mA (max)

Nominal coil current

Medium current changeover relay — Part number: 6G9T-14B192-D_

Medium current normally open relay — Part number: 6G9T-14B192-C_ (pin 4 not present)

Battery Disconnect Relay

Battery Disconnect Relay Parameters

260 Amps @ 25°C

Normally continuous rated current (B-A)

3.3 Amps @ 25°C for 60ms

Nominal excitation coil current

High Power Bi-stable relay — Part number: BK2T-10B728-A_

4.15.3 Windscreen Wipers

The base wiper system should not be tampered
with (controlled by BCM and multiplex
architecture with LIN technology).

NOTE:

Power to wiper motors is limited by the

size of the wiring and associated relays. If any
alternative wiper installation is made, it must have
a specification equivalent to Ford components.

Refer to: 5.8 Glass, Frames and Mechanisms

(page 169).

Date of Publication: 04/2012

FORD

TRANSIT CUSTOM

2012.75

4 El

ec
tric

119

Summary of Contents for TRANSIT CUSTOM 2012.75

























































































































































































Search results

Summary of Contents for TRANSIT CUSTOM 2012.75

Reviews:

Related manuals for TRANSIT CUSTOM 2012.75

Brands by name

Popular brands

Ford TRANSIT CUSTOM 2012.75, Mounting Manual

Search results

Summary of Contents for TRANSIT CUSTOM 2012.75

Reviews:

Related manuals for TRANSIT CUSTOM 2012.75

Brands by name

Popular brands