Ford MUSTANG MACH 1 2021 Page 59 Supplement Manual Download

Page: 59 / 84

ENGINE SPECIFICATIONS

Description

Item

90 degree V8.

Configuration.

3.66 in (93 mm) bore x 3.65 in (92.7 mm)

stroke.

Bore x stroke.

307 in³ (5,038 cm³)

Displacement.

12.0:1

Compression ratio.

0.049 in (1.25 mm) - 0.053 in (1.35 mm)

Spark plug gap.

480 hp (358 kW) @ 7000 RPM

Horsepower.

420 lb.ft (569 Nm) @ 4600 RPM

Torque.

7500 RPM

Redline.

168 mph (270 km/h)

Top speed with manual transmission
without gurney flap.

155 mph (249 km/h) Electronically limited.

Top speed with automatic transmission.

Dual overhead cams - roller finger

followers.

Valvetrain.

Coil on plug.

Ignition.

3.4 in (87 mm)

Throttle body.

Cast aluminum.

Pistons.

Forged steel cross-plane.

Crankshaft.

Forged steel.

Connecting rods.

Naturally aspirated cold air induction.

Induction.

High-flow dual exhaust with H-pipe and

active valve mufflers.

Exhaust system.

Mustang (CZG) Mach 1, enUSA, First-Printing

Capacities and Specifications

Summary of Contents for MUSTANG MACH 1 2021





















































































Search results

Summary of Contents for MUSTANG MACH 1 2021

Reviews:

Related manuals for MUSTANG MACH 1 2021

Brands by name

Popular brands

Ford MUSTANG MACH 1 2021, Supplement Manual

Search results

Summary of Contents for MUSTANG MACH 1 2021

Reviews:

Related manuals for MUSTANG MACH 1 2021

Brands by name

Popular brands