Ford MUSTANG MACH 1 2021 Page 39 Supplement Manual Download

Page: 39 / 84

TOWING POINTS

(IF EQUIPPED)

Recovery Hook Location

E265227

The recovery hook is in the spare wheel
storage tray.

Installing the Recovery Hook

There is an installation point for the
recovery hook behind the towing eye
attachment point cover.

To remove the towing eye attachment
point cover:

E333098

Gently press at the position indicated
until the left side of the cover pops out.

2. Gently remove the cover from the front

fascia by pulling on the left side of the
cover, away from the vehicle.

Note:

The towing eye attachment point

cover has a small lanyard to keep it
attached to the bumper. Disconnect the
lanyard if necessary.

To install the recovery hook:

E146284

Insert the recovery hook and turn it
counterclockwise to install it. Make sure
that you fully tighten the recovery hook.

Note:

The recovery hook has a left-hand

thread.

To re-install the towing eye attachment
point cover:

Insert the right side of the cover into
the front fascia. There is a protruding
edge on the cover that inserts into the
fascia.

2. Push the left side of the cover into the

front fascia until it is aligned with the
fascia and you hear a snap.

Mustang (CZG) Mach 1, enUSA, First-Printing

Roadside Emergencies

Summary of Contents for MUSTANG MACH 1 2021





















































































Search results

Summary of Contents for MUSTANG MACH 1 2021

Reviews:

Related manuals for MUSTANG MACH 1 2021

Brands by name

Popular brands

Ford MUSTANG MACH 1 2021, Supplement Manual

Search results

Summary of Contents for MUSTANG MACH 1 2021

Reviews:

Related manuals for MUSTANG MACH 1 2021

Brands by name

Popular brands