Ford MKZ 2008 Page 78 Owner'S Manual Download

Page: 78 / 281

This acts as a reminder that these warning conditions still exist within
the vehicle.

Warnings

Status

Driver’s door ajar

Warning cannot be reset (CLOSE
DOOR TO RESET) will be displayed

Passenger door ajar

Left rear door ajar

Right rear door ajar

Park brake engaged

RELEASE PARK BRAKE will be
displayed

Low fuel level

Warning returns after 10 minutes

Check brake system

Check park aid

Warning returns after the ignition key
is turned from OFF to RUN

Low brake fluid

Low tire pressure

Tire pressure monitor fault

Tire pressure sensor fault

Trunk ajar

Clear objects by pass seat

Compass error

Lamp outage

Integrated key programming
status

Maximum number of Integrated Keys
exceeded

DRIVER DOOR AJAR.

Displayed when the driver’s door is not

completely closed.

PASSENGER DOOR AJAR.

Displayed when the passenger side door is

not completely closed.

REAR LEFT DOOR AJAR.

Displayed when the rear left door is not

completely closed.

REAR RIGHT DOOR AJAR.

Displayed when the rear right door is not

completely closed.

PARK BRAKE ENGAGED.

Displayed when the park brake is engaged.

If the warning stays on after the park brake is off, contact your
authorized dealer as soon as possible.

CHECK BRAKE SYSTEM.

Displayed when the brake system needs

servicing. If the warning stays on or continues to come on, contact your
authorized dealer as soon as possible.

2008 MKZ

(378)

Owners Guide (post-2002-fmt)
USA

(fus)

Driver Controls

Summary of Contents for MKZ 2008


























































































































































































































































































Search results

Summary of Contents for MKZ 2008

Reviews:

Related manuals for MKZ 2008

Brands by name

Popular brands

Ford MKZ 2008, Owner'S Manual

Search results

Summary of Contents for MKZ 2008

Reviews:

Related manuals for MKZ 2008

Brands by name

Popular brands