Ford Granada 1985-1994, Owner'S Manual

Page: 208 / 254

20 When refitting, check the switch for
correct operation before refitting the shrouds
and steering wheel centre cover. When fitting
the shrouds, be careful not to trap the switch
rubber gaiter.
Models from April 1992
21 Note that if access to the switch retaining
screws cannot be gained with the steering
wheel in position, then the steering wheel
must first be removed.
Windscreen wipe/wash switch
Models before April 1992
22 Proceed as described in the previous sub-
section for the direction indicator switch.
Depending on equipment, the wipe/wash
switch may have more than one multi-plug
connected to it.
Models from April 1992
23 Note that if access to the switch retaining
screws cannot be gained with the steering
wheel in position, then the steering wheel
must first be removed.
Door pillar switch (for courtesy
light)
24 Remove the single securing screw and pull
the switch from its location (see illustration).
25 Retain the wiring with (for instance) string
or a clothes peg, so that it cannot fall into the
door pillar, then disconnect the switch.
26 Lubricate the plunger of the switch with a
little petroleum jelly when refitting
Reversing light switch (manual
gearbox)
27 Raise the front of the vehicle and support
it securely.
28 Locate the reversing light switch, which is
located on the right-hand side of the gearbox.
29 Disconnect the wiring from the switch,
wipe clean around it and unscrew it.
30 When refitting, make sure that the switch
wiring is routed sufficiently far from the
exhaust system to avoid damage due to heat.
Window operating switch
31 The window operating switch is removed
from the armrest or console in the same way
as the mirror control switch previously
described
(see illustration).
Sliding roof switch
32 Carefully prise the switch from the overhead
console using a thin-bladed screwdriver.
33 Disconnect the multi-plug and remove the
switch.
Tailgate lock switch
34 The tailgate lock switch controls the
luggage area lights. When appropriate, it also
provides inputs to the auxiliary warning and
anti-theft systems.
35 To avoid damage to other components,
the battery must be disconnected before the
tailgate lock switch is removed.
36 Remove the tailgate interior trim panel,
which is secured by eleven screws.
37 Release the switch locking tab, pivot the
switch away from the lock and disconnect it.
38 When refitting, make sure that the slot on
the switch engages with the operating lug on
the lock barrel.
Handbrake “ON” switch
39 Gain access to the base of the handbrake
lever by removing the rubber gaiter and (if
necessary) the centre console or switch panel
(see illustration).
40 Disconnect the wiring from the handbrake
switch. Undo the two screws and remove the
switch, noting how the screws do not pass
through holes in the lever but engage in slots.
41 After refitting the switch, check for correct
operation before refitting the surrounding trim.
Stop-light switch
42 Remove the under-dash trim on the
driver’s side. The trim is secured by plastic
clips.
43 Disconnect the wiring from the switch.
Turn the switch 90° anti-clockwise and
remove it from the brake pedal bracket (see
illustration).
44 When refitting, hold the pedal in the fully
raised position, push in the switch and turn it
clockwise to lock it. Release the pedal and
check that at least 2 mm (0.08 in) of the switch
plunger is visible (see illustration).
Oil pressure warning switch
All engines except DOHC
45 This switch is located on the left-hand side
of the cylinder block. Access may be impeded
by one of the manifolds and associated
equipment.
46 Disconnect the wire from the switch, then
unscrew the switch and remove it.
47 Clean the switch and its seat before
refitting. Apply a little sealant to the switch
threads if wished.
48 Run the engine and check that there are
no oil leaks from the switch. Stop the engine
and check the oil level.
DOHC engines
49 On these engines the switch is located on
the right-hand side of the cylinder block
between the core plugs.
13•12 Body electrical system
15.24 Door pillar switch securing screws
(arrowed)
15.43 Stop-light switch fitted to brake
pedal bracket
15.44 Fitting the stop-light switch (A)
Plunger protrusion (between arrows) must be
at least 2 mm (0.08 in)
15.31 Removing a window operating switch 15.39 Handbrake “On” switch