Ford 2011 Mustang Page 173 Owner'S Manual Download | Manualshive

Page: 173 / 348

background image

Increasing the inflation pressure beyond this pressure will not increase
the tire’s load carrying capability.

•

kPa:

Kilopascal, a metric unit of air pressure.

•

PSI:

Pounds per square inch, a standard unit of air pressure.

•

Cold inflation pressure:

The tire pressure when the vehicle has

been stationary and out of direct sunlight for an hour or more and
prior to the vehicle being driven for 1 mile (1.6 km).

•

Recommended inflation pressure:

The cold inflation pressure found

on the Safety Compliance Certification Label or Tire Label located on
the B-Pillar or the edge of the driver’s door.

•

B-pillar:

The structural member at the side of the vehicle behind the

front door.

•

Bead area of the tire:

Area of the tire next to the rim.

•

Sidewall of the tire:

Area between the bead area and the tread.

•

Tread area of the tire:

Area of the perimeter of the tire that

contacts the road when mounted on the vehicle.

•

Rim:

The metal support (wheel) for a tire or a tire and tube assembly

upon which the tire beads are seated.

INFLATING YOUR TIRES

Safe operation of your vehicle requires that your tires are properly
inflated. Remember that a tire can lose up to half of its air pressure
without appearing flat.

Every day before you drive, check your tires. If one looks lower than the
others, use a tire gauge to check pressure of all tires and adjust if
required.

At least once a month and before long trips, inspect each tire and check
the tire pressure with a tire gauge (including spare, if equipped). Inflate
all tires to the inflation pressure recommended by Ford Motor Company.

You are strongly urged to buy a reliable tire pressure gauge, as automatic
service station gauges may be inaccurate. Ford recommends the use of a
digital or dial-type tire pressure gauge rather than a stick-type tire
pressure gauge.

Use the recommended cold inflation pressure for optimum tire
performance and wear. Under-inflation or over-inflation may cause
uneven treadwear patterns.

Tires, Wheels and Loading

173

2011 05+ Mustang

(197)

Owners Guide, 1st Printing
USA

(fus)

«
...
171
172
173
174
175
...
»

Summary of Contents for 2011 Mustang





























































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Mustang

Brand: TATA Motors Pages: 94

Brand: GÄN Pages: 24

Brand: Q'STRAINT Pages: 10

Brand: Tessera4x4 Pages: 20

Gold Cruuse Cruisecontrol GC90

Brand: John Gold Pages: 24

Brand: Whispbar Pages: 14

Brand: Actia Pages: 37

Brand: AC Schnitzer Pages: 20

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: Honda Pages: 85

Brand: Hummer Pages: 502

Brand: Nav TV Pages: 4

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: Guidosimplex Pages: 8

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Thule Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands