Force Computers PENT/CPCI-721, Installation Manual

Page: 75 / 126

Controls, Indicators, and Connectors On-Board Connectors
PENT/CPCI-721 3 - 9
Figure 22: PENT/CPCI-721 CompactPCI J5 Connector Pinout
I/O-721
In addition to its CompactPCI interface the I/O-721 provides the fol-
lowing CompactPCI connectors (see below).
The interfaces available on the CompactPCI interface can be routed to
interface-dependent standard connectors via the IOBP-IO720.
J1 and J2
The J1 and J2 connectors implement the CompactPCI 64-bit connector
pinout as defined by the CompactPCI specification. Therefore, this
manual only documents the pinout of the J5 connector.
J5
Besides the CompactPCI specific pinout the following ports are avail-
able on the I/O-721 CompactPCI J5 connector (the name used in the fol-
lowing pinout is given in brackets):
• 16-bit SCSI (SCSI)
• VGA (VGA)
• User I/O pins for PMC slot 1 (PMC 1 I/O)
reserved
ETH TX+
MSE clock
1st IDE /CS3
2nd IDE /CS1
1st IDE A1
IDE IORDY
2nd IDE DRQ
IDE D12
IDE D7
IDE D2
FD DRATE0
FD /MTR0
FD /STEP
FD /RDATA
LPT Slct
LPT /Slctin
LPT Data 6
LPT Data 1
COM2 DTR
COM1 RI
COM1 TxD
D C
reserved
ETH RX+
MSE data
USB P1–
2nd IDE /CS3
1st IDE /LED
2nd IDE A1
1st IDE DAK
1st IDE /IOW
IDE D13
IDE D8
IDE D3
FD MSEN0
FD /MTR1
FD /TRK0
FD /WDATA
LPT /Error
LPT Data 7
LPT Data 2
COM2 RTS
COM2 DCD
COM1 DTR 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
ETH RX–
reserved
IDE /DIAG
USB P1+
IDE /RST
2nd IDE /LED
1st IDE A0
2nd IDE DAK
2nd IDE /IOW
IDE D14
IDE D9
IDE D4
Vcc
FD /DR0
FD /INDEX
FD /WGATE
LPT /Ack
LPT Strobe
LPT Data 3
COM2 CTS
COM2 DSR
COM1 DSR
E
reserved
reserved
KBD data
2nd IDE A2
1st IDE /CS1
2nd IDE IRQ
2nd IDE /IOR
1st IDE DRQ
IDE D11
IDE D6
IDE D1
FD DENSEL
FD /WP
FD /DIR
LPT Pe
LPT /Init
LPT Data 5
LPT Data 0
/PBRESET
COM2 TxD
COM1 CTS
COM1 RxD
SMI
ETH TX–
KBD clock
1st IDE A2
2nd IDE A0
1st IDE IRQ
1st IDE /IOR
IDE D15
IDE D10
IDE D5
IDE D0
FD /DR1
FD /DSKCHG
FD /HDSEL
Vcc
LPT Busy
LPT /Autofeed
LPT Data 4
COM2 RI
COM2 RxD
COM1 RTS
COM1 DCD
B A