manualshive.com logo in svg

FOR-A USF-106DC-12G, Operation Manual, Page: 36 / 58

Share
Download
FOR-A USF-106DC-12G Operation Manual Download Page 36

36 

<If 

Monosum

 is selected> 

 

 

Item 

Default 

Setting 

Description 

Source 1-8 L 

Embedded Ch.1-15 (Odd ch) 

Embedded  

Ch.1-16 

Selects an audio source 
channel input to each 
Monosum L and R. 

Source 1-8 R 

Embedded Ch.2-16 (Even ch) 

 
< If 

Test

 is selected> 

 

 

Item 

Default 

Setting 

Description 

Test Tone 

Off 

Off 
500Hz Tone 
1kHz Tone 

Allows you to assign an audio test signal 
to the embedded audio on the SDI 
output. 

 
 

5-2-6. Gain 

Selecting 

Gain 

in the Audio Block diagram opens the following menu screen. 

 

 

Item 

Default 

Setting (increments) 

Description 

Master Mute 

Disable 

Disable 
Enable 

Setting to 

Enable

 mutes all output 

audio channels. 

Ch.1-16 

0.0dB 

-20.0dB  to  +20.0dB (0.1) 

Sets the gain for each channel.  
Pressing 

Unity

 resets values. 

Master 

0.0dB 

-20.0dB  to  +20.0dB (0.1) 

Sets the gain offset for all channels. 
Pressing 

Unity

 resets values. 

Summary of Contents for USF-106DC-12G



























































Reviews:

No comments